Plan a pilot box
Menu

Camera or flatbed? Digitizing negatives and slides in an archive

Reader question: For a collection of film negatives, slides and transparencies, should we use a flatbed scanner, a film scanner or a camera on a copy stand, and how do we judge quality?

By Dastok Editorial TeamIssue: Published

For an archive’s negatives and slides, a camera on a copy stand over an even light source is the most flexible choice, a dedicated film scanner suits steady runs of 35mm and medium format, and a flatbed with a transparency unit is a workable fallback for sheet film and small budgets. The FADGI Technical Guidelines recommend all three, plus planetary scanners, for film, and advise against drum scanners. Quality is judged the same way whatever the device: by capturing film targets and measuring them against the star level you specified. Choose the device by format mix, condition, volume and who will turn negatives into positives.

The forum threads that dominate this question test one roll at home. This article works at archive scale: thousands of mixed frames, film bases that can be hazardous, color negatives that need interpretation, and a quality standard you can check.

What FADGI says about film scanning equipment

The third edition of the FADGI Technical Guidelines lists film scanners, planetary scanners, digital cameras and flatbed scanners as recommended for negatives and transparencies, and drum scanners as not recommended. Its equipment chapter then explains why the categories matter less than measured results.

Cameras

FADGI describes digital cameras as having “become first line digitization tools in the cultural heritage community.” It notes that cameras with 100 to 150 megapixel sensors are common, and that color filter patterns mean “the true resolution is less than the stated resolution.” It also notes that a few cameras use monochrome sensors without the filter pattern, which can suit black-and-white material.

Film scanners

FADGI calls film scanners “perhaps the least understood class of digitization equipment.” Under the hood, it says, they are “really either a planetary scanner or digital camera, with the exception of true drum scanners.” What sets them apart is software that interprets the film, which FADGI calls “an especially difficult task for negatives since they lack a visual scene reference.”

Flatbeds

The guidelines are frank about flatbeds. “Few of this breed, though, have a place in a cultural heritage digitization project,” they say, and “for almost every application where a flatbed scanner might be used, there is a better solution using other tools.” They also say flatbeds “have their place and may be appropriate for some applications,” and advise: “Beware of fantastic claims of resolution or dynamic range. Rely on digital image conformance evaluation testing to verify the results.”

Drum scanners

Drum scanners spin the original on a drum. FADGI grants that they “provide the highest image quality of all imaging devices,” but “due to the risk of damage to originals and inherently slow speed, they are inappropriate for most cultural heritage digitization.”

What every film setup needs

Whatever the device, FADGI’s notes for negatives and transparencies set the same requirements:

  • Lenses of “flat field design” that focus all colors at the same plane (apochromatic); “lenses designed for general imaging are not appropriate for close focusing film scanning applications.”
  • An aperture found by testing, “generally one to two f stops from maximum aperture.”
  • Exposures short enough that vibration does not cost resolution. FADGI warns that vibration effects “become much more noticeable when imaging at high magnifications, as is common in film digitization.”
  • A dim working environment, because ambient light and lens flare degrade tone and color.

Camera, film scanner or flatbed: how they compare

Each device can produce good masters of some film; none is best for every format. The differences that matter in an archive are which formats fit, whether edges and notches can be captured, how glass and dust are handled, and how much operator judgment each frame needs.

Question Camera on a copy stand Dedicated film scanner Flatbed with transparency unit
Formats Any size, with the right lens, holders and light source Usually fixed to the formats its holders accept Strips, slides and sheet film, as its holders allow
Full frame with edges and notches Possible with suitable holders or masks Often limited by the film carrier Depends on the holder
Glass against the film Optional Depends on the holder Common; film may rest on glass
Who interprets the negative The technician, in processing software Scanner software, adjusted by the operator Scanner software, adjusted by the operator
FADGI status for film Recommended Recommended Recommended, with cautions
How quality is proven Film targets and analysis software Film targets and analysis software Film targets and analysis software

Camera on a copy stand

A camera station photographs film laid over an even light source. Its advantages in an archive are flexibility and control. One station can handle 35mm strips, roll film, sheet film and mounted slides with a change of holder and lens, and the operator sees each capture at once. The cost is skill: lens choice, alignment, exposure and inversion all sit with the technician. FADGI’s accessories note applies in full: “an imaging system must be parallel at the sensor, lens, and object planes.”

A working station has a few parts beyond the camera. The light source should have a color rendering index above 90, which FADGI calls “generally accepted as appropriate for most cultural heritage imaging.” Mask the light around the film, because “reduction of stray light around the original will considerably reduce flare,” and use a lens hood. Holders should keep the film flat without covering its edges, and the copy stand should be checked for vibration with the room’s normal traffic and equipment running.

Dedicated film scanner

A film scanner bundles optics, light source and interpretation software for specific formats. It can be efficient for long, uniform runs. Its limits show with mixed collections: holders that crop the frame edge, formats it cannot take, and automatic interpretation that must be controlled so the archival master stays unclipped.

Film scanners also change with their software. FADGI advises characterizing each device “using the specific software/device drivers to be used for production,” and again after every update, because performance “can change dramatically (and not always for the better)” when drivers change. Before relying on one, scan a film target with the exact settings planned for production and turn off any automatic exposure or color correction you cannot document.

Flatbed with a transparency unit

A flatbed reads film through glass with light from the lid. FADGI’s own example of a varied workflow notes that negatives “will need backlighting either with a light box on a copy stand or a particular setting on a flatbed scanner.” Its notes on photographs add a caution that applies to film on glass too: “dust and dirt on the scanner glass and optical system can result in dust and dirt in the file.” Flatbeds are most defensible for larger sheet film, where the sampling rates FADGI asks for are lower, and for programs that cannot yet staff a camera station.

How much resolution film needs, and how it is measured

FADGI sets far higher sampling rates for film than for paper, because the film is small and the image is enlarged. For 35mm up to 4x5 inch negatives and transparencies, three-star means at least 3,000 ppi and four-star 4,000 ppi, with 16-bit masters at both levels.

FADGI category One-star Two-star Three-star Four-star Bit depth at 3 and 4 star
3.9 Transparencies, 35mm up to 4x5 in 1,000 ppi 2,000 ppi 3,000 ppi 4,000 ppi 16
3.10 Transparencies, 4x5 in and larger 500 ppi 1,000 ppi 1,500 ppi 2,000 ppi 16
3.11 Negatives, 35mm up to 4x5 in 1,000 ppi 2,000 ppi 3,000 ppi 4,000 ppi 16
3.12 Negatives, 4x5 in and larger 500 ppi 1,000 ppi 1,500 ppi 2,000 ppi 16

The 4x5 inch size appears in the titles of both categories, so a specification should name which category it applies to 4x5 sheet film. Our article on FADGI star ratings explains what the star levels measure beyond sampling.

What those numbers mean in pixels

The arithmetic is simple: inches of film times ppi. A full 35mm frame of 24 by 36 mm is about 0.94 by 1.42 inches.

Original Sampling Pixels Megapixels
35mm frame, 24 × 36 mm 3,000 ppi (three-star) about 2,835 × 4,252 about 12
35mm frame, 24 × 36 mm 4,000 ppi (four-star) about 3,780 × 5,669 about 21
4x5 in sheet film 1,500 ppi (3.12 three-star) 6,000 × 7,500 45
4x5 in sheet film 3,000 ppi (3.11 three-star) 12,000 × 15,000 180

The last two rows show why the category choice for 4x5 film matters: the same sheet is four times the pixels under 3.11. For comparison, the National Archives’ 2004 access guidelines aimed at about 4,000 pixels across the long side of a 35mm original, “approx. 2800 ppi.” The scanning resolution calculator gives pixel dimensions and file sizes for any frame you enter.

Sampling is not detail

A camera or scanner can save a file at 4,000 ppi without recording 4,000 ppi of detail. FADGI measures what the system resolves with a spatial frequency response target, and warns that for all film work “captures are made at very high magnifications, which exaggerate vibration and other image quality degrading artifacts.” Its advice: “measure and monitor the quality of captures using standard film targets and analysis software.”

Two limits are specific to film. FADGI notes that for transmissive analysis “only B&W targets are currently available,” and that its tone and color values for transmissive material are provisional. And film “cannot be related to a reproduction scale, unless there is a physical measurement in the image,” so film is digitized at resolutions “relative to the size of the film and the capabilities of the digitization system.”

FADGI’s free AutoSFR program, listed on its OpenDICE page, was developed to help imaging professionals “determine the actual resolution present in images,” which helps set the scanning resolution for a specific collection. Test a few typical frames before fixing the specification.

File sizes and color mode

FADGI’s negative tables allow “grayscale or color as appropriate” at every star level, and ask for 16 bits per channel at three and four stars. For black-and-white negatives the choice is real. The National Archives’ 2004 guidelines suggest scanning older black-and-white negatives in color, because stains and discolored base can then be reduced by choosing the cleanest channel.

Color triples the data. Uncompressed, one 35mm frame at four-star works out as follows:

35mm frame at 4,000 ppi, 16 bits per channel Uncompressed size
Grayscale (one channel) about 42.9 MB
Color (three channels) about 128.6 MB

At three-star, 3,000 ppi, the same frame is about 24.1 MB in grayscale and 72.3 MB in color. FADGI lists TIFF and JPEG 2000 as master formats for film, and lossless compression reduces these figures. Multiply by the number of frames and by the copies you keep before choosing color for a black-and-white collection.

Film bases first: nitrate, acetate and polyester

Before choosing a device, find out what the film is made of. Cellulose nitrate is a fire hazard, cellulose acetate can decay and spread its decay, and both decide how film is stored, moved and handled at the scanner.

NEDCC’s short guide to film base materials names three broad types: cellulose nitrate, cellulose acetates and polyester. The first two “are unstable,” and “the products of their degradation can severely harm and even destroy photographic collections, in addition to posing serious safety hazards.”

Cellulose nitrate

Eastman Kodak began selling negatives on flexible cellulose nitrate film in August 1889, and nitrate film stayed in production “until the early 1950s.” NEDCC advises that a collection with flexible transparent negatives from 1890 to 1950 “is very likely to contain at least some nitrate film,” and that such negatives “should immediately be separated from other negatives.”

Identification clues, from NEDCC and the National Archives:

  • Edge printing reading “NITRATE,” on some films. Copies carry the edge printing of their originals, so the word alone does not settle it.
  • On Kodak sheet film, a V-shaped notch first from the edge identifies pre-1949 nitrate; a U-shaped notch identifies acetate.
  • Kodak’s nitrate sheet film production ended in 1939, although safety sheet film was test-marketed from the mid-1920s, so date alone is not reliable.
  • Deterioration signs: fading or silver mirroring, yellowing, tackiness, curling or brittleness, and an acidic nitric smell.

Two format notes from NEDCC help with mixed boxes. Photographers often bought bulk 35mm motion picture film and loaded it into cassettes, so NEDCC warns that still negatives on nitrate can turn up for “an additional 13-year period” after Kodak’s cutoff date for that format. Amateur roll films were not edge-marked, NEDCC notes, but “can be identified by their tendency to curl very tight scrolls.”

The National Archives warns that nitrate “can pose a serious fire risk when stored improperly,” points to NFPA 40 for storage, and notes federal regulations on transporting and disposing of nitrate film. It advises that nitrate “should be duplicated or digitized by a knowledgeable company or person specially trained to handle nitrate film.” Ask any vendor how they meet those requirements before anything is packed.

Cellulose acetate

Acetate “safety” film replaced nitrate from the 1920s and, in the National Archives’ words, “was predominantly used until the 1970s.” It can develop vinegar syndrome “at any point in time,” especially in warm, humid storage. Signs include dimensional change, crystals, bubbles or channels, brittleness, and “most typically a strong odor similar to that of vinegar.” The Image Permanence Institute’s A-D Strips measure the acidity and help prioritize.

The National Archives’ guidance is to isolate deteriorating film and “prioritize the reformatting of deteriorating film.” NEDCC agrees: “Any negatives that show signs of deterioration should be digitized as soon as possible.”

Polyester

Polyester was introduced in the mid-1950s, and the National Archives notes that “most sheet film from the 1970s onwards is polyester based.” It “is dimensionally stable and does not distort, break, or tear easily.” Under crossed polarizing filters polyester shows rainbow-colored interference patterns, a simple non-destructive test that NEDCC also describes. NEDCC lists three other tests, all destructive, to be used only when other identification fails.

Handling at the scanner

  • Wear clean nitrile gloves; the Library of Congress suggests gloves for negatives, and the National Archives says to handle sheet film with gloves, avoiding the image area.
  • Remove loose dust with a hand-operated blower or a clean soft brush. Both the Library and the National Archives advise against canned air.
  • “Do not attempt to clean film with water-based solutions or other chemicals,” says the National Archives.
  • Do not write on sheet film, even along the edges; write on the enclosure.
  • Film kept in cold storage must warm up before it is opened. NEDCC suggests 8 to 12 hours at room temperature for film sealed in bags with its boxes.

Our condition assessment checklist includes the film checks, and the collection care page covers custody of originals.

What to capture first

Condition sets the order more than subject does. NEDCC’s rule is that “the more advanced the stage of deterioration, the sooner the negative should be reformatted to minimize the amount of image detail lost.” For nitrate, it notes that most negatives keep legible detail into the third of six stages of decay, while later stages have shrinking areas of legible image and should go into cold storage or be digitized “before the image completely fades away.”

Film in good condition still benefits. NEDCC advises that nitrate and safety negatives that need to be handled “should still generally be digitized,” so the digital image can be used “while the original remains in cold storage.” It adds a caution: have a digital preservation policy in place before deciding that the only retained copy of a negative will be digital.

Originals before copies

Where both an original negative and a print or duplicate exist, capture the original. FADGI notes that “every generation of photographic copying involves some quality loss.” NEDCC’s leaflet on duplicating historical negatives makes the same point about prints: “A print always has detail loss and a compressed tonal range when compared to the original negative.” Prints and copy negatives become the source only when the original is lost or too damaged to handle.

Capturing the whole frame: edges, notches, sleeves and glass

The archival master should show the whole piece of film, edge to edge, because edges carry notch codes, edge printing and frame numbers. Glass helps flatten film but brings its own artifacts.

FADGI is specific: “If there is important information on a mount or in the border of a negative, then scan the entire mount and the entire negative including the full border. Notch codes in sheet film are often considered important to retain.” It also names the obstacle: “Typical film carriers cover a small portion of the film area, ruling out imaging all the way to the edge of the film.”

Glass and Newton’s rings

The alternative to a carrier is to sandwich film between glass, which FADGI says introduces “the possibility of Newton’s rings, dust and other artifacts.” Its conclusion: “Imaging without glass generally will result in a superior scan, and is therefore preferred if possible.” Where glass is needed, FADGI highly recommends antireflective glass, noting that this “is not anti-Newton glass commonly used in the past for film scanning.”

FADGI adds a technique for black-and-white film: narrow-band blue light with a monochrome camera “has been shown to increase the resolution and reduce the effects of Newton’s rings.” The note limits it to monochrome cameras, because blue light “harms the resolution for a standard Bayer sensor camera.”

Sleeves, envelopes and slide mounts

Negative sleeves and envelopes can carry the only caption. Capture them as separate images linked to the frames by file name. Slide mounts may carry handwriting or printed dates; capture the mount when it holds information, as FADGI asks for mounts. Large-format film and glass have their own handling questions, covered in our guide to digitizing glass plate negatives.

Negatives into positives: inversion and color

FADGI’s method is to scan the negative as if it were a transparency, keep that unclipped image as the archival master, and make the positive as a separate production master. Turning a negative into a positive is interpretation, and the guidelines say so.

1 Archival master 2 Production master 3 Access copy Negative scanned as a transparency Highlights and shadows unclipped Whole frame, edges and notches included Inverted to a positive Tone and color set by the technician Adjustments logged No dust removal Cropped, spotted or retouched if wanted Edits noted in file name and metadata Made from master 2
How one negative becomes three files. Based on the FADGI Technical Guidelines, Third Edition (2023), sections 3.8, 3.11, 3.12 and 6.3, checked November 2026.

The archival master

FADGI’s recommended method: “Scan the negative as if it is a transparency, taking care to assure that both highlights and shadows are not clipped.” On an 8-bit scale, values “should not be less than 5 in the shadows or more than 250 in the highlights,” with exposure adjusted for the film base density. “Save this image as the archival master.”

Because there are few calibration targets for negative film, FADGI recommends setting scan values “based on highlight, shadow, and midtone measurements of the image being scanned,” and warns these settings “may need to be changed with every scan.” That one line explains much of the time film capture takes.

The production master

To make the production master, the image is inverted and adjusted. FADGI’s comparison is the darkroom: “Digitizing negatives is analogous to printing negatives in a darkroom and is very dependent on the photographer’s or technician’s skill and visual literacy to produce a good image.” It must be done on a calibrated monitor.

For black-and-white film, the National Archives’ 2004 guidelines suggest scanning older negatives in color, because staining, discolored base and retouching can be minimized by choosing the color channel that best suppresses them before converting to grayscale.

Color negatives

Color negatives are harder. FADGI explains that the orange cast “is primarily a proportional dye mask” meant for the print material, and that both mask and dyes fade over time. It concludes that “there is no way to reliably create a digital image from a negative that is a faithful reproduction of how the image may have looked if printed with the original materials and processes of the era.” It adds that color negative films made before 1975 (C-22 process) “do not scan well.”

FADGI highly recommends inversion programs that use “scene balancing” algorithms. Whatever the tool, keep the archival master untouched so a better interpretation can be made later.

Who makes the positive

Decide before capture who will invert and adjust: the vendor, your staff, or both in turn. Because the production master is an interpretation, write down the intent, for example “a neutral, full-range print look, no restoration,” and ask that adjustments be logged. FADGI’s code of ethics recommends documenting “the imaging process and any special processing performed on master digital objects.” With the negative master kept, a curator can commission a different positive years later without handling the film again.

Slides and transparencies

Slides are positives, so the target is the original itself: “the tonal scale and color balance of the digital image should match the original transparency being scanned.” FADGI notes that transparency film can have a maximum density approaching 4.0, a range that challenges optics and sensors, and that “Kodachrome films cannot be profiled correctly using an Ektachrome IT-8 target.” For Kodachrome, it suggests a professionally produced Kodachrome profile.

Dust, scratches and infrared cleaning

Clean film physically before capture, leave the dust that remains in the archival master, and do any digital spotting on access copies. Hardware dust removal in scanners, which many people call infrared cleaning, is limited by film type, and it is not appropriate for masters in any case.

What FADGI allows

FADGI’s notes for photographs state that “dust removal is not allowed on master images, and digital dust removal techniques during the scanning process are also not approved.” Its general rule is that editing out artifacts “should only be done to derivative files.” The FADGI code of ethics lists “removal of blemishes in the original such as stains, dust, or scratches” among enhancements to avoid on masters.

Why scanner dust removal fails on black-and-white negatives

Many readers ask why their scanner’s hardware dust removal, such as DIGITAL ICE, does nothing useful on black-and-white negatives. The scanner makers’ own documentation answers it. Epson’s quick guide for its Perfection 4990 says the feature “supports color and chromogenic (dye-based) black and white film,” and advises not to use it “with conventional black and white negative film or Kodachrome film.” Its Perfection V700 guide says, of monochrome negatives, “only chromogenic monochrome negative film is supported,” and that Kodachrome is not supported.

Epson’s guides add two cautions that matter for archives. Scanned images “may become softer in texture” with the feature, and using it on film without dust or scratches may leave the image “distorted or blurred.” For an archival master, that is two reasons to leave it off.

Physical cleaning

Use a hand-operated blower, as both the National Archives and the Library of Congress advise. The National Archives also allows a light touch with a clean, soft brush, while the Library cautions that even soft brushes can scratch. Keep the light box, holders and any glass clean, since FADGI warns that dust on scanner glass and optics ends up in the file. Clean between batches, not once a day. Anything that will not lift with air is part of the film’s current condition and stays in the archival master.

Throughput at archive scale

In an archive, throughput depends on much more than the device’s capture speed: handling, sleeving, cleaning, setting exposure for each frame and inverting all take time. Time a real batch of your own film on each candidate setup before choosing.

FADGI’s small-project workflow notes why film is slow: setting controls once from a target and keeping them for every scan “should work reasonably well for reflection scanning, but will be much harder to do when scanning copy negatives, copy transparencies, original negatives, and original slides/transparencies.” Each frame may need its own exposure decisions.

What to time in a test

  1. Handling: removing film from sleeves, checking base and condition, cleaning.
  2. Loading: placing frames in holders or on the light box and aligning them.
  3. Capture: exposure decisions and the capture itself.
  4. Interpretation: inversion and adjustment of the production master.
  5. Quality control and logging, including sleeve captures and file naming.

Example (fictional). A later accession at the Aster County Historical Society brings in the Wren Gulch Courier’s negative files: about 1,900 frames of 35mm in strips, 500 sheets of 4x5 film, and 200 mounted color slides. The condition survey finds a vinegar smell in two boxes of 35mm, and three sheets of 4x5 film with V-shaped notches, so those are separated and flagged as possible nitrate before anything else happens.

A timed test on 100 frames of each format gives the society its own numbers. For 35mm strips, the camera station averages 60 frames an hour including handling and inversion, against 35 an hour on the flatbed, where edges are cropped by the holder. For 4x5 sheets, the flatbed reaches 3.12 three-star at 1,500 ppi with the full sheet in frame and averages 20 sheets an hour, close to the camera’s 22. The society chooses the camera station for 35mm and slides and the flatbed for 4x5, with the acetate boxes captured first.

Turn your own timed rates into a schedule with the project timeline calculator, and size the storage for 16-bit film masters with the storage calculator.

Checking film captures before the film goes back

Film captures fail in ways paper captures do not: clipped densities, flipped images, Newton’s rings and cropped edges. Check each batch against a short film-specific list while the film is still at the station.

FADGI’s inspection list for all image files includes several items that matter most for film: “Image- horizontally or vertically flipped,” clipping of “detail lost in high values (highlights) or dark values (shadows),” and artifacts including “dust” and “Newton’s rings.” It recommends visually inspecting at least 10 images or 10 percent of each batch, whichever is larger, at 100 percent magnification.

A film-specific checklist:

  1. The archival master shows the whole film, including edges, notches and edge printing.
  2. The histogram of the archival master has no values piled at either end; FADGI’s 8-bit limits are 5 in the shadows and 250 in the highlights.
  3. The production master reads correctly, not mirrored, with any visible lettering the right way round.
  4. No Newton’s rings, glare or holder edges intrude on the image area.
  5. Dust and scratches in the image match the film’s condition, not dirt on glass or the sensor.
  6. Sleeve and envelope images are linked to the right frames by file name.
  7. The frame count matches the inventory, with blank and fogged frames recorded, not skipped.

Our image QC checklist covers the general file and image checks that sit alongside these.

A decision table by format and volume

Use the table as a starting point, then confirm the choice with a timed and measured test on your own film.

Your film Suggested route Why Watch for
A few hundred mixed 35mm frames and slides Camera on a copy stand, or a film scanner already on hand Either can meet three-star with testing; volume does not justify new equipment Edge cropping by carriers; automatic inversion settings
Thousands of 35mm frames in strips Camera station with a strip holder One setup, operator sees each frame, full edges possible Alignment and vibration at high magnification
Thousands of mounted slides Camera station, or a film scanner tested on a sample Slides are positives; color can be matched to the original Mount information; Kodachrome profiling
Medium-format roll film Camera station Adapts to mixed frame sizes with suitable holders Film curl; glass and Newton’s rings
4x5 in and larger sheet film Flatbed with transparency unit, or camera with tiles Lower ppi for larger film; a flatbed may hold the full sheet Category choice (3.11 or 3.12); dust on glass
Acetate with vinegar syndrome First in the queue, on whichever route is ready NEDCC and the National Archives say to prioritize deteriorating film Brittleness, shrinkage, isolation from other film
Suspected nitrate Specialist handling only, after identification Fire risk and federal transport rules Storage under NFPA 40; trained handlers
Glass plate negatives and lantern slides Camera station with full support Glass is heavy and fragile See the glass plate article

For very large sheet film, FADGI allows capture in tiles and stitching, with the stitched file as the production master and the tiles as the archival master.

What to do next

Start with identification, not equipment. Knowing the film bases, formats and condition of the collection settles most of the decision.

  1. Survey a sample of boxes: formats, film base clues, notch codes, odors and sleeve information.
  2. Separate suspected nitrate and deteriorating acetate, and record them in the inventory.
  3. Write the FADGI category and star level for each format, naming the category for 4x5 film.
  4. Run a timed test of 100 frames per format on each candidate setup, with film targets, and read the measurements.
  5. Decide who makes the positives, and require untouched negative masters alongside them.
  6. Check every batch with the film checklist above, including edges, clipping, dust and orientation.

A short test on your own film is the honest way to compare devices. Our guide to running a digitization pilot shows how to structure one, and the photo and negative scanning page describes how Dastok, a Colorado Springs company that digitizes historical documents, photographs and museum collections, captures film as an untouched negative master with a separate positive.

Working through this with a real collection?

If this article describes a decision you are facing, tell us about the collection. A pilot box answers most questions with your own material.

Plan a pilot box

Studio and contacts

24 South Weber Street, Suite 225
Colorado Springs, CO 80903
(719) 244-8450sales@dastok.com