Plan a pilot box
Menu

Scanning resolution and file size calculator

Enter the size of an original and the resolution you plan to capture it at, and see the pixel dimensions and how large each master file will be.

Calculator

Fictional example values are filled in. Replace them with your own; results update as you type. Nothing you enter leaves your browser.

Pixels per inch at the size of the original.

Results

Pixel dimensions
3,400 × 4,400 px
Megapixels
15.0 MP
Uncompressed image data
44.9 MB
Long edge
4,400 px
Printable size at 300 ppi
11.33 × 14.67 in

Size is the raw pixel data (width × height × channels × bytes per channel). An uncompressed TIFF adds a small header; lossless compression usually makes files smaller. MB here means one million bytes.

Resolution decides how much detail a digital image can hold, and it sets the size of every master file you will store for decades. The calculator above turns the size of an original and a capture resolution into pixel dimensions, megapixels and the size of the uncompressed image data, so you can test a capture specification before anyone scans a page.

Pixels per inch of the original

Capture resolution here means pixels per inch (ppi) measured at the size of the original: how many pixels the image spends on each inch of the actual letter, photograph or map. It is not a screen or printer setting, and it does not depend on the camera or scanner. An 8.5-inch-wide sheet captured at 400 ppi is 3,400 pixels wide, whatever made the image.

This is why small originals need large numbers. A 35mm negative is less than an inch and a half wide, so it takes thousands of pixels per inch to produce an image of useful size. A map several feet wide reaches the same pixel count at a modest ppi.

Bit depth and channels

  • Channels. Color images have three channels (red, green and blue). Grayscale images have one, so they are a third of the size.
  • Bit depth per channel. Eight bits give 256 levels of tone in each channel. Sixteen bits give 65,536 levels, which keeps finer steps between tones when an image is adjusted later, as with dense negatives or faded prints. Sixteen bits also double the data.

The formula in plain words

  1. Width in pixels = width in inches × ppi, and the same for the height.
  2. Megapixels = width in pixels × height in pixels ÷ 1,000,000.
  3. Uncompressed size in bytes = width in pixels × height in pixels × channels × (bit depth ÷ 8). The calculator divides by 1,000,000, so one MB here is one million bytes.
  4. Printable size at 300 ppi = pixels ÷ 300 for each side.

FADGI ppi minimums

The Federal Agencies Digital Guidelines Initiative (FADGI) publishes the Technical Guidelines for Digitizing Cultural Heritage Materials, third edition (2023). It sets a minimum ppi for each category of material at each star level, each with a small tolerance. A few rows:

Material (FADGI section) Two-star Three-star Four-star
Unbound manuscripts, rare and special (3.3) 250 300 400
Unbound documents, general collections (3.4) 250 300 400
Bound volumes, rare and special (3.1) 250 300 400
Newspapers (3.7) 250 300 400
Prints and photographs (3.8) 250 400 600
Negatives, 35mm up to 4x5 in (3.11) 2,000 3,000 4,000
Negatives, 4x5 in and larger (3.12) 1,000 1,500 2,000

Resolution alone does not earn a star level. FADGI determines a rating by measuring images against its evaluation parameters, using targets and analysis software. FADGI also “does not recommend digitization to less than a three-star level when possible, and cautions against imaging to four-star level for all but the most sophisticated imaging programs.” On a Dastok project, the category and target level for each kind of material are agreed in writing, and capture is checked against those targets.

Reading the results

  • Pixel dimensions and megapixels describe the image itself.
  • Uncompressed image data is the raw pixel data. An uncompressed TIFF adds a small header, and lossless compression usually makes files smaller. Multiply by your image count in the storage calculator.
  • Long edge is the number to use when you set the size of access copies or the deepest zoom in a viewer.
  • Printable size at 300 ppi shows how large a print the file could make. It is a check, not a target.

Limits

  • Ppi counts samples, not sharpness. An image out of focus at 600 ppi holds less detail than a sharp one at 400.
  • Measure the original with the margin you will keep in frame. The calculator adds no margin.
  • Color accuracy, noise and lighting are outside this tool. The image QC checklist covers them.

Worked example

Example (fictional). Some of Ida Okerlund’s letters in Box 3 of the Aster County Historical Society are in faint pencil, so the society asks for 400 ppi, in color, at 8 bits per channel, for its letter-size sheets of 8.5 × 11 inches. Each sheet becomes 3,400 × 4,400 pixels, or 15.0 megapixels. The uncompressed image data is 44.9 MB (3,400 × 4,400 × 3 channels × 1 byte). The long edge is 4,400 pixels, and the file would print at 11.33 × 14.67 inches at 300 ppi. In FADGI’s table for unbound manuscripts, 400 ppi is the four-star minimum and 300 ppi the three-star minimum.

Change one input Pixels Uncompressed size
16 bits per channel 3,400 × 4,400 89.8 MB
Grayscale (1 channel) 3,400 × 4,400 15.0 MB
300 ppi 2,550 × 3,300 25.2 MB

The capture pages for documents, photographs and negatives and maps and oversize items describe how each material is handled. The Reading Room’s capture and imaging section covers standards in more depth, and a pilot box shows what a specification produces on your own originals.

Send one box first.

A pilot box shows you the images, the recognized text and the catalog records before you commit a whole collection. Tell us what is in the box and what you want people to find.

See your originals captured in a pilot box

Studio and contacts

24 South Weber Street, Suite 225
Colorado Springs, CO 80903
(719) 244-8450sales@dastok.com