Plan a pilot box
Menu

Digitizing glass plate negatives: handling, capture and files

Reader question: How do we safely handle and digitize a collection of glass plate negatives, including cracked plates, and which files should we keep?

By Dastok Editorial TeamIssue: Published

To digitize glass plate negatives safely, handle each plate by two opposite edges with nitrile gloves, one plate at a time, and capture it with light passing through it, on a camera copy stand over an even light source or on a flatbed scanner with a transparency unit. Include the whole plate, edges, notes and damage in the frame, and keep that capture as an untouched negative master. Make the positive and any retouched copies as separate files. Cracked, broken and flaking plates need support, a conservator’s advice and their own housing; afterwards, store intact plates upright in paper enclosures and broken ones flat.

This guide is written for historical societies, local museums and special collections with a few dozen to a few thousand plates. It follows the work in order: what you have, how to survey it, handling, damaged plates, cleaning, capture, inversion and files, rehousing, and a worked example.

What glass plate negatives are, and why they need their own workflow

A glass plate negative is a photographic image layer, the emulsion, coated on one side of a sheet of glass. It is heavy, it breaks, and its emulsion can flake, so it needs handling and capture methods that paper and film do not.

Two processes, two sets of risks

Most American collections contain one or both of two processes. The Library of Congress care and handling leaflet dates collodion wet plate glass negatives to 1851 to 1885 and gelatin dry plate glass negatives to 1880 to 1920, as the years they were introduced and most popular. A 2026 article in the VRA Bulletin on a small college’s dry plate collection describes the gelatin plates in that collection as sold “pre-cut” and “pre-emulsified,” which, the authors note, reduced barriers to use.

The process matters because the binders react differently. The American Institute for Conservation’s wiki on surface cleaning warns that solvent cleaning “requires accurate process identification,” and gives an extreme example: mistaking a collodion print for a gelatin one and applying alcohol “would dissolve it and the image would be removed.” Its glass chapter adds that collodion binders and varnish layers “tend to be very sensitive.” If you have plates that may predate the mid-1880s, ask a photograph conservator to identify them before anyone cleans or treats anything.

Sizes and weight

Plates come in many sizes, so measure and record each one. Conservation guidance refers to plates from 4 by 5 inches to more than 10 by 12 inches, and the size decides both the storage box and the capture category. FADGI, the federal digitization guidelines, splits negatives at 4 by 5 inches, as the capture section below explains.

Weight is the hazard people forget. The National Archives’ guidance on housing glass plates recommends half-size boxes for plates 8 by 10 inches and smaller “as the plates can be heavy,” and says boxes for plates over 10 by 12 inches “should only be partially filled.”

What goes wrong with them

The Northeast Document Conservation Center’s leaflet on duplicating historical negatives notes that “glass-plate negatives can break easily,” and lists signs of deterioration including “breakage, flaking, fading, discoloration.” The glass itself can decay too: the AIC wiki describes “sick glass,” with weeping and crystal formation, and says water and humid storage in cellars or attics contribute to it.

Lantern slides are different

Lantern slides are positive images on glass made for projection. The National Archives’ guidance on moving glass plates notes that “lantern slides bound with intact cover glasses do not require individual enclosures.” They are captured as transparencies, not negatives, and this guide does not cover them in detail.

Survey and sort the plates before anyone scans

A condition survey sorts every plate into intact, flaking, cracked or broken before capture begins, so the fragile ones are found while they are still in their boxes. It takes less time than it sounds, and it decides the handling, capture setup and housing for each group.

What to record for each plate

  1. Identifier. Number the enclosures, not the plates. The Library of Congress page on caring for photographs advises avoiding marks on photographs and says “it is preferable to mark the photograph’s housing materials.”
  2. Size, measured in inches.
  3. Condition: intact, minor flaking, significant flaking, cracked or broken, using the definitions below.
  4. Writing and marks: anything on the enclosure, the box or the edges of the plate.
  5. Old enclosures: keep any envelope or sleeve with writing on it, or capture it before it is replaced.

Our condition assessment checklist has a section for photographs, negatives and glass that you can print and use at the table.

Sorting by condition

The National Archives’ housing guidance separates minor from significant flaking, and that distinction is useful at the survey table. Minor flaking means “a few small edge losses, and glass chipping at the edges where the emulsion appears stable and secure at the loss site.” Significant flaking means “flaking edges with hanging flaps which could be torn off” or “cracking overall with blind cleavage at the interior (looking like a dry mudflat).”

ConditionHandlingCaptureHousing afterward
Intact, stable emulsionTwo opposite edges, gloves, one at a timeStandard transmissive setupPaper sleeve with side seams, upright on the long edge
Minor flaking at edgesAs intact, with care at the edgesStandard setup; note lossesSleeve with a handling note
Significant flaking or cleavageMinimal; never slide in or out of a sleeveCapture once, then use the digital copyFour-flap enclosure, upright; sink mat and flat if high value
Cracked, still in one pieceFlat, on a rigid supportSupported, with light controlled at the crackSupported with glass or ragboard inside its enclosure
Broken into piecesFlat only; shards never touchingPieces aligned on a support, not gluedSink mat or board sandwich in a four-flap, stored flat
Summary of National Archives housing and moving guidance for glass plate negatives and the Library of Congress care leaflet, checked November 2026. Treatment decisions for damaged plates belong with a photograph conservator.

Prioritize by risk and use

Capture the most fragile plates early, while they can still be captured, but only after you have practiced on sound ones. Plates with significant flaking are the strongest case for digitization, because the National Archives advises duplicating them and then avoiding “handling the original plates after duplication.” Plates people ask for often are next, since NARA also notes that “even plates in good condition will be damaged from regular use.”

How to handle glass plates safely

Work on a clean, flat, dry surface, wear nitrile or latex gloves, and hold each plate by two opposite edges, one plate at a time. Never press on a plate, write on it, stack plates or hold a plate by one corner.

The National Archives rules

The National Archives’ housing page sets out the handling procedure in a few lines, and it is worth posting beside the workstation:

  • Work “on a clean, flat, dry surface, free of any debris.”
  • Wear “non-vinyl plastic gloves when handling the plates: Latex or Nitrile, for example.” The reason: “Cotton can be slippery when handling glass and may snag flaking emulsion.”
  • “Handle plates by two opposite edges. Never hold them by one edge, or the corner.”
  • “Place glass plates emulsion side up when you lay them flat on a surface.”
  • “Never place any pressure on the plate: do not press, lean, or write on top of it.”
  • “Never stack the plates while you are working with them. Only work with one at a time.”
  • “Label your sleeves before placing the plates into them.”

The AIC wiki is blunter about cotton: “The most common cause of breakage in the lab is the object slipping out of the conservator’s hands when wearing cotton gloves.” FADGI adds that washing and thoroughly drying hands before handling is “critical” and that “hand sanitizer should not be used.”

Finding the emulsion side

You need to know which side carries the image before you lay a plate down or place it on a scanner. The VRA Bulletin authors describe checking by holding the plate carefully up to a light source: “the emulsified side will have a matte, cloudy hue that extends to the outer edges of the plate and may appear slightly silver or purple in color.” The other side is plain, shiny glass. Note which side faced the lens in your capture log, so the positive can be oriented correctly later.

Moving plates around the building

Carry intact plates the way they are stored, upright on a long edge. The National Archives’ moving guidance says to move intact plates “in their storage orientation, that is, resting vertically on one long edge,” and to keep broken plates flat. The same page asks for carts rated for the weight of glass and for corrugated filler boards that keep plates from shifting inside their boxes. Our collection care page describes the same rules for originals in a studio or on site.

Cracked, broken and flaking plates

Support cracked and broken plates flat, keep broken pieces from touching each other, and do not glue or tape anything. Capture them as they are, and leave repair to a photograph conservator.

Cracked plates

A cracked plate is still one object, but it can come apart when lifted. The Library of Congress leaflet says “cracked plates should be supported with a piece of glass or lignin-free ragboard inside their envelopes or sleeves.” Lift the support, not the plate. For capture, keep the plate on its support if the support is clear glass, or move it once onto the capture surface by sliding a rigid sheet beneath it.

Broken plates

The AIC wiki states the first rule: “It is very important that broken shards do not come into contact with each other,” because contact causes chipping and further breakage. For capture, lay the pieces in their original positions on a clean sheet of glass over the light source, with a hairline gap between them. The VRA Bulletin team did exactly this with twelve broken plates in a collection of 193: the fragments “were gently laid next to each other but not permanently reconstructed,” because binding substances could cause further damage.

Expect lighting problems. The same team found that light “would glare through the small cracks,” making some areas brighter than others. Lower the light intensity, use diffusion between the light and the glass, and accept a master that shows the cracks. If the plate matters enough to repair, the Library of Congress is clear: “A photograph conservator should perform repair of a broken plate.”

Flaking emulsion

Flaking plates lose image every time they move, so handle them as few times as possible. Capture them once, carefully, and make the digital file the use copy. For significant flaking, the National Archives houses plates “in four-flap enclosures” so they are never slid in and out of a sleeve, and stores “very high value plates with extensive flaking/cleavage” sink-matted and flat, with the note “Flaking glass plate: handle with extreme caution. Use duplicate copy.”

When to stop

FADGI’s negative sections end with a sentence worth adopting as a rule: “In any situation where there is potential harm to the original, stop immediately and seek assistance.” Plates stuck together, plates stuck to their sleeves, mold, and emulsion lifting as you watch are all reasons to stop and call a conservator. The American Institute for Conservation keeps a directory of conservators by specialty, which the Library of Congress care page points to.

Cleaning: what is safe and what is not

Limit cleaning to loose dust, removed with a hand blower or a very soft brush, and only on plates with sound emulsion. Anything wet, any solvent and any treatment of damaged emulsion is a conservator’s decision.

Dry dusting

The National Archives’ Holdings Maintenance guide for photographs allows light brushing with a clean, soft brush or a “hand operated puff-style blower,” and says “canned air should be avoided due to the force of the air stream and potentially damaging propellants.” It adds a limit that matters for glass: “Do not dust a torn photograph, one with cracked or lifting emulsion, or one that is highly significant.” The Library of Congress warns that “even soft brushes can scratch,” so the blower comes first.

Why not wipe or wash

Wet cleaning and solvents can swell or dissolve the binder. The AIC wiki explains that solvent cleaning “requires accurate process identification” and that “unpredictable damaging effects may occur.” The National Archives’ photograph guidance stops at dusting and refers damaged or highly significant items to a photograph conservator. For a volunteer at a work table, the safe rule is simple: if a puff of air does not move it, leave it and capture it.

Clean the equipment, not the image

Dust on scanner glass, a light box or a copy board ends up in the file. FADGI asks for routine cleaning of “scanners, platens, and copy boards,” recommends a HEPA vacuum for the workspace, and suggests considering anti-static devices. It is equally firm that dust in the file stays in the master: for photographs, “dust removal is not allowed on master images, and digital dust removal techniques during the scanning process are also not approved.”

Capturing the plate: camera or flatbed

Capture glass plates in transmitted light, either with a digital camera on a copy stand over an even light source or with a flatbed scanner and transparency unit. FADGI lists planetary scanners, digital cameras and flatbed scanners as recommended technologies for negatives 4 by 5 inches and larger, and lists drum scanners as not recommended.

Camera and light source

A camera setup handles every plate size, keeps the plate on its own support, and avoids glass-on-glass contact. FADGI’s guidance for negatives asks for lenses “of a flat field design” that focus all colors at the same plane, an aperture found by testing that “is generally one to two f stops from maximum aperture,” and a dimly lit room “to reduce the effect of ambient light.” For black-and-white negatives, it notes that monochrome cameras, especially with a blue filter over the light source, give “far better results” than standard color sensors.

The VRA Bulletin team’s experience shows why the light source matters. Their makeshift light sources, including a phone flashlight, caused overexposure and lost detail, and they concluded that “a professional-grade lightbox would have evenly illuminated the details.” For in-house work, an even, color-stable light panel larger than your biggest plate is the purchase to make first.

A camera station for plates can be set up in an afternoon. A workable order:

  1. Level the light panel and the camera, so the sensor is parallel to the plate. A small bubble level on each is enough.
  2. Mask the light around the plate with black card, so the only light reaching the lens passes through the plate. FADGI notes that lens flare “will reduce the purity of color reproduction and distort the tonality of an image,” and asks that exposures minimize “flare from non-image sources.”
  3. Place a support sheet of clean glass on the panel for cracked and broken plates, so they never need to be lifted on their own.
  4. Focus manually on the emulsion, using magnified live view rather than autofocus.
  5. Capture a target at the start of the session and whenever settings change.
  6. Check every capture at full size and against the histogram before the plate goes back in its sleeve. A retake is cheap; another handling session is not.

Flatbed with a transparency unit

A flatbed with a transparency lid can work well for small runs of plates in good condition. Its risks are contact and fit. The VRA Bulletin authors note that contact between plate and scanner glass “can cause chipping, scratching, and other forms of damage,” and that holders that lift plates off the bed may not fit “the non-standard sizes and thicknesses of vintage glass plates.” FADGI adds that imaging between glass can introduce Newton’s rings and dust, and that anti-reflective glass is “highly recommended” where glass is used. Do not put broken or flaking plates on a flatbed.

Our article on camera or flatbed for negatives and slides compares the two setups in more depth, including cost and throughput.

Resolution, bit depth and format

FADGI’s Technical Guidelines (third edition, 2023) give minimum sampling rates for negatives by size and star level:

FADGI category One-star Two-star Three-star Four-star
3.11 Negatives, 35mm up to 4x5 in 1,000 ppi 2,000 ppi 3,000 ppi 4,000 ppi
3.12 Negatives, 4x5 in and larger 500 ppi 1,000 ppi 1,500 ppi 2,000 ppi

For category 3.12, FADGI specifies 8-bit files at one and two stars and 16-bit at three and four stars, in TIFF or JPEG 2000, grayscale or color “as appropriate.” Capture in color if stains, colored retouching or the tint of the glass carry information you want to keep; grayscale files are a third the size. Our guide to FADGI star ratings explains what the levels measure, and the scanning resolution calculator converts ppi into pixels and megabytes for your plate sizes.

Exposure and targets

FADGI’s method for negatives is to “scan the negative as if it is a transparency,” without clipping highlights or shadows: on an 8-bit scale, values “should not be less than 5 in the shadows or more than 250 in the highlights.” It acknowledges a “lack of calibration targets available for negative films,” so settings may need to change with each plate, while recommending standard film targets and analysis software to monitor quality. In practice, image a transmission target at the start of each session and check a histogram for every plate.

Capture the whole plate: edges, notes and damage

Frame the entire plate with a small border around it, including its edges, any writing and every crack, chip and loss. The master records the plate as an object, damage included; cleaned-up versions come later and are labeled as derivatives.

Include the edges

FADGI’s section on cropping recommends that “the entire object be scanned, without cropping,” with “a small border” visible around it, and says that if there is important information “in the border of a negative, then scan the entire mount and the entire negative including the full border.” Plate edges can carry what a catalog needs: numbers, initials or captions written or scratched by the photographer, paper masks, tape, and the profile of chipped corners. FADGI’s rule for derivatives completes the instruction: “Crop with a border for whole artifact information and crop inside edges for access.”

Record damage as it is

FADGI states the principle directly: “Digitized material should document the appearance of the original at the time of capture, not what it may once have looked like if restored to its original condition.” Among the enhancements it says to avoid are “digital infill” and “removal of blemishes in the original such as stains, dust, or scratches,” and it limits such editing to derivatives: “Editing out artifacts should only be done to derivative files.”

For glass plates this matters for two reasons. A crack across a face is evidence of the plate’s history and condition, and a future conservator or researcher may need to see exactly where it ran. And the master may become the only record of an image if a flaking plate continues to deteriorate.

Extra images for damaged plates

A single transmitted-light image can hide the condition of the emulsion. FADGI allows “alternate imaging techniques,” such as different lighting, and says that if they produce several files of the same original, “these images must be referenced as a group in file naming and embedded metadata,” with one file identified as the base. For a flaking or cracked plate, consider adding a reflected-light image of the emulsion side at a low angle, grouped with the transmitted-light master, as a condition record.

Capture the sleeves and boxes too

The envelope or sleeve is often the only caption a plate has. Photograph any enclosure or box with writing on it and link the image to the plate’s identifier, before the old enclosure is replaced or set aside.

Inversion and the files to keep

Keep three kinds of file: the negative as captured (the archival master), an inverted positive with tonal adjustments (the production master), and access copies, which may be retouched if they say so. The negative master is never edited; every positive can be remade from it.

Glass plate transmitted light Archival master negative, as captured full plate, no edits TIFF, 16-bit Production master inverted positive, tone adjusted Access copies cropped, JPEG; retouched only if labeled Grouped with master condition image, sleeve and box images Blue: never edited. Lime: adjusted, can be remade from the master.
The file set for one plate, following the FADGI Technical Guidelines (third edition, 2023) on negatives, cropping and alternate imaging, checked November 2026.

The archival master is a negative

FADGI’s method is explicit: after scanning the negative as a transparency, “save this image as the archival master. To create a production master from the above, invert the image to produce a positive image.” The master keeps the plate’s full tonal information, its border and its damage, and nothing in it depends on someone’s taste.

The positive is an interpretation

Inversion is not a neutral step. FADGI compares digitizing negatives to “printing negatives in a darkroom” and says it is “very dependent on the photographer’s or technician’s skill and visual literacy.” It goes further: given the many historical combinations of plates and printing papers, “there is no way to reliably create a digital image from a negative that is a faithful reproduction of how the image may have looked if printed with the original materials and processes of the era.” Its stated worry is that “modern sensibilities of what an image should look like will lead to scans which lose the authenticity of the original.”

The practical answer is to keep the negative master and treat every positive as a version. Note the adjustments in the file’s embedded metadata, as FADGI asks for adjusted access versions, and you can remake the positive later with better judgment or software. For plates whose image reads backward because of how they were captured, flip the production master, not the archival master, and record the change.

Our guide to FADGI star ratings also notes that FADGI calls its tone and color values for transmissive originals “provisional,” another reason the untouched master is the safe reference.

Access copies may be enhanced, if they say so

Access copies are where restoration belongs, if you want it. The VRA Bulletin team, for example, produced public images by applying Clarity and Shadows adjustments to camera raw files and then Invert, Black and White and Levels layers in Photoshop, with five adjustments per image. That is a reasonable access workflow, as long as the unadjusted capture is kept and the access copy says what was done. FADGI’s rule is that adjustments “may be made to access versions, and noted as such in embedded metadata and file naming.”

Names that keep the set together

Give every file the plate’s identifier plus a role, for example ACHS-7-G031_neg.tif, ACHS-7-G031_pos.tif, ACHS-7-G031_raking.tif and ACHS-7-G031_sleeve.tif. The file naming builder can generate a consistent pattern from your collection, box and item numbers.

What the capture log should say

For each plate, record the identifier, size, condition group, the side that faced the lens, the capture setup (camera or flatbed, light source, ppi and bit depth), the target result for the session, and every adjustment made to the production master and access copies. Put the same facts in each file’s embedded metadata where your software allows it. Taste and software change; with the log and the untouched master, whoever makes the next one can see exactly what was done before.

Rehousing after capture

After capture, put intact plates in individual paper enclosures and store them upright on their long edges in strong, partly filled boxes. Broken plates go flat, in sink mats or between boards, in shallow boxes labeled to be carried flat.

Intact plates

The National Archives houses intact plates “individually in loosely-fitting, buffered paper sleeves with side seams,” with the emulsion “away from the seams,” because the emulsion is “easily abraded” and seam adhesives may harm the image. The plates are stored “vertically, on the long edge, in document boxes,” with corrugated board interleaved “every inch,” filler boards front and back if the box is not full, boxes stacked “two high, no more,” and labels reading “CAUTION, FRAGILE, GLASS, and HEAVY.”

The Library of Congress agrees on vertical storage and adds that plates “larger than 5 x 7 inches are ideally stored in cabinets with rigid metal dividers spaced every 1 to 1 1/2 inches.” NEDCC’s leaflet on the care of photographs puts it in one line: “Glass plate negatives require vertical storage in order to prevent breakage. If broken or degrading, glass plate negatives may be stored horizontally.”

Enclosure materials

Use paper or board that passes the Photographic Activity Test (PAT), which the Library of Congress care page describes as part of ISO 18902’s requirements for photo-safe storage materials. NEDCC advises avoiding kraft paper, glassine and PVC. Paper suits glass better than plastic: it is opaque, porous, easy to label in pencil, and the Library of Congress warns that photographic emulsions “may stick to plastic enclosures if they are exposed to high RH, especially above 70% RH.”

Broken plates

For broken plates, the National Archives describes two housings. Plates of high intrinsic value go flat in “protective sink mat enclosures made from corrugated board,” with the fragments aligned and a small space between them, held apart by small spacers glued to the base of the mat. Others are sandwiched “between two sheets of buffered board” inside a four-flap enclosure, stacked “no more than 5 deep in a shallow box labeled BROKEN GLASS-STORE AND CARRY HORIZONTALLY.” The Library of Congress adds that plates larger than 8 by 10 inches should be stacked only two deep because of their weight.

The room they live in

The Library of Congress leaflet says glass plate negatives “should be stored at 30-40% RH to minimize glass decomposition and flaking,” and the AIC wiki cites the same range, explaining that below 30 percent the binder desiccates and above 40 percent the glass starts to hydrate. For temperature, the Library’s care page recommends 70°F or below, and both it and NEDCC ask for relative humidity to fluctuate by less than 5 percent a day. Keep glass out of attics and basements, and off the floor.

If plates travel to an outside studio for capture, the packing and transport checklist covers upright packing in padded slots, and the National Archives’ moving guidance covers foam interleaving for warped plates and custom crates for oversize ones.

A worked example: one box of studio plates

The example below follows one fictional box through survey, capture and rehousing, with storage figures worked out for its plate sizes.

Example (fictional). The Aster County Historical Society, whose Box 3 holds the Okerlund family papers, also has Box 7: 64 glass plate negatives from the Halvorsen Studio in Wren Gulch, the studio whose imprint appears on cabinet card ACHS-3-C04. A volunteer and the collections manager survey the box in one afternoon. They find 40 plates measuring 4 by 5 inches and 24 measuring 5 by 7 inches. Of the 64, 55 are intact, 4 have minor flaking at the edges, 2 have significant flaking, 2 are cracked but whole, and 1, ACHS-7-G031, is broken into four pieces. Three sleeves carry pencil captions, including “Lund school, 1896.”

They capture the 55 intact plates first, on a camera stand over a light panel, to practice. All plates are 4 by 5 inches or larger, so they fall in FADGI category 3.12, and the society chooses three-star: 1,500 ppi, 16-bit grayscale TIFF. With a quarter-inch border on each side, a 4 by 5 plate becomes about 6,375 by 7,875 pixels, roughly 100 MB uncompressed, and a 5 by 7 plate about 7,875 by 10,875 pixels, roughly 171 MB. The archival masters for the box come to about 8.1 GB before compression, and the positive production masters about the same again.

The two significantly flaking plates are captured next, each once, with an added low-angle reflected-light image of the emulsion side. The two cracked plates are captured on the glass sheets that now support them. For ACHS-7-G031, the collections manager slides the pieces, still on their board, onto a clean glass sheet over the light panel, aligns them with hairline gaps, dims the light to reduce glare at the cracks, and captures the plate as it is, cracks and all. The positive shows three pupils and a teacher in front of a frame schoolhouse; the access copy, with the cracks softened, is labeled “digitally retouched for access.”

Afterward, the 59 plates that are intact or have minor flaking go back upright in buffered paper sleeves with side seams, in half-size boxes labeled fragile, glass and heavy. The two flaking plates go into four-flap enclosures, upright. The cracked plates stay on their supports, and ACHS-7-G031 goes flat between buffered boards in a four-flap enclosure in a shallow box marked to be carried flat. A conservator is asked to advise on the broken plate.

The example shows the order that keeps risk low: survey first, practice on sound plates, capture fragile plates once, and rehouse each condition group differently. The schoolhouse plate also shows why sleeves matter: its only caption was on the envelope. Identifying the people in plates like these is the next job, covered in our article on cataloging unidentified photographs.

What to do next

Start with a survey, not a scanner. Knowing how many plates you have, in which sizes and conditions, tells you whether this is a few weeks of volunteer work with a light panel or a project for a conservator and an imaging studio.

Checklist

  1. Survey every plate for size, condition and writing, numbering enclosures rather than plates.
  2. Separate the damaged plates into flaking, cracked and broken groups before anyone handles them for capture.
  3. Set up the workstation: clean flat surface, nitrile gloves, a blower, an even light source larger than your largest plate, and a support sheet for damaged plates.
  4. Choose a FADGI level in writing for each size category, and test it on a few sound plates.
  5. Capture the full plate, border and damage included, and keep the negative as the untouched archival master.
  6. Make positives and access copies as separate, labeled files.
  7. Capture sleeves and boxes that carry writing, and link them to the plate.
  8. Rehouse by condition, upright for intact plates and flat for broken ones, at 30 to 40 percent relative humidity if you can manage it.
  9. Call a photograph conservator for stuck, moldy, broken or actively flaking plates.

If you need help

Historical societies sometimes hold a box or two of plates from a local studio; our page for historical societies describes how a small first batch can be scoped around material like this. If you would rather have the plates captured outside, our photo and negative scanning page explains how we capture glass in transmitted light, keep the negative master untouched and deliver the positive separately. Either way, the survey you make first is the part only you can do, because you know which plates your community asks for.

Working through this with a real collection?

If this article describes a decision you are facing, tell us about the collection. A pilot box answers most questions with your own material.

Plan a pilot box

Studio and contacts

24 South Weber Street, Suite 225
Colorado Springs, CO 80903
(719) 244-8450sales@dastok.com