Plan a pilot box
Menu

FADGI star ratings: which level does your collection need?

Reader question: What do FADGI's one-to-four star levels actually measure, and which level should we require for each kind of material in our collection?

By Dastok Editorial TeamIssue: Published

FADGI star ratings grade how well a digitization setup performs when its images of a reference target are measured: tone, color, sharpness, noise, evenness of light and scale, plus a minimum sampling rate in pixels per inch (ppi). One star is a reference copy for finding the original, two stars is the professional minimum, three stars is a very good image for most uses, and four stars is the best imaging practical today. For most historical collections, require three-star for preservation masters, name the FADGI material category for each series, and ask for the target measurements that show the level was met.

That answer comes from the third edition of the FADGI Technical Guidelines for Digitizing Cultural Heritage Materials, published in May 2023. The rest of this article reads those guidelines in plain language. It maps materials and purposes to a sensible level, explains why “FADGI-certified scanner” is a misleading phrase, and lists what a vendor’s target report should contain.

What FADGI star ratings actually measure

A FADGI star rating is a grade earned by measured image performance, not a property of a scanner or camera. The guidelines say a digital object’s star rating “is determined by meeting the FADGI evaluation parameters through image analysis.”

FADGI is the Federal Agencies Digital Guidelines Initiative, hosted by the Library of Congress. Its Still Image Working Group wrote the third edition in 2022 and 2023, updating the 2016 edition. The line of descent runs back to the National Archives’ 2004 technical guidelines, on which FADGI’s 2010 version drew substantially.

How a measurement works

The method is simple to describe. A technician captures a reference target, a printed card of gray patches, color patches, edges and a scale, under the same light and settings used for the originals. Analysis software compares the captured values with the target’s known values. Each result is then checked against a tolerance that depends on the material category and the star level you asked for.

The guidelines are explicit that targets and software are part of the method. They are “intended to be used in conjunction with digital image conformance evaluation targets and software,” and they call that pairing “an essential element of a FADGI-conforming imaging program.”

The parameters behind a rating

Every material category in chapter 3 of the guidelines has its own table. The table below gives the three-star and four-star limits for one common category, 3.4 Documents (Unbound): General Collections, with a plain description of what each parameter catches.

Parameter What it checks Three-star limit Four-star limit
Sampling frequency Pixels per inch on the original at least 294 ppi (300 ppi minus 2%) at least 396 ppi (400 ppi minus 1%)
Tone response (OECF), ΔL*2000 Whether grays come out at the right lightness under 3 under 1.5
White balance, ΔE(a*b*) Whether grays are neutral, without a color cast under 4 under 2
Lightness uniformity How evenly the light covers the field under 3% under 1%
Average color accuracy, mean ΔE2000 Average color error across all patches under 3.5 under 2
Color accuracy, 90th percentile Color error on the worst patches under 7 under 4
Color channel misregistration Red, green and blue fringes at edges under 0.5 pixel under 0.33 pixel
SFR10 (sampling efficiency) How much of the pixel count becomes real detail over 80% over 90%
SFR50 Sharpness, which must fall inside a band 40% to 75% 45% to 65%
Reproduction scale accuracy Whether the ppi in the file header matches real size within 2% within 1%
Sharpening (maximum modulation) Artificial edge enhancement under 1.05 under 1.02
Noise, standard deviation of L* Grain and electronic noise in flat patches under 2 under 1

Read the table this way: an image meets three-star only if every required parameter sits inside the three-star column. Some rows in the guidelines, such as gain modulation and SFR response at the Nyquist frequency, are marked informative in this edition and do not decide conformance.

Minimum sampling (ppi) Higher is stricter 200 250 300 400 1 star2 star3 star4 star Mean color error (ΔE2000) Lower is stricter 6.5 5 3.5 2 1 star2 star3 star4 star SFR10 sampling efficiency (%) Higher is stricter 60 70 80 90 1 star2 star3 star4 star Noise (std. dev. of L*) Lower is stricter 4 3 2 1 1 star2 star3 star4 star
How four tolerances tighten from one star to four for FADGI category 3.4, Documents (Unbound): General Collections. The three-star bar is dark. Source: FADGI Technical Guidelines, Third Edition (2023), section 3.4, checked November 2026.

What changed in the 2023 edition

If a vendor’s documentation predates 2023, check it against the current edition (PDF). The third edition made several changes that affect specifications:

  • Values moved to L*a*b*. Tolerances are now colorimetric. FADGI says earlier 8-bit count values “do not validate FADGI conformance for newly-produced images” and are “no longer valid for 2023 version conformance.”
  • One star dropped for rare material. One-star specifications were removed for the rare and special collections categories.
  • A pass-or-fail category arrived. Documents (Unbound): Modern Textual Records, with values from the National Archives, has no star levels at all: “either the images meet the specifications above or they do not.”
  • Staff became part of conformance. Professional staff joined the components of the FADGI conformance program, and gain modulation was added as an informative measure.

The four star levels in FADGI’s own words

FADGI defines its levels in a short narrative, and the exact wording matters when you write a specification. Three stars is the level the guidelines steer most programs toward.

Level FADGI’s description ISO 19264-1 level
One star “appropriate for applications where the intent is to provide a reference to locate the original” None; FADGI offers it “for reference use only”
Two star “the minimally acceptable rating for most professional digitization activity” Level C
Three star “a very good professional image that is appropriate for most uses” Level B
Four star “the best imaging practical today” Level A

The ISO column comes from FADGI’s own text. The international standard is ISO 19264-1:2021, Photography, Archiving systems, Imaging systems quality analysis, Part 1: Reflective originals. FADGI describes its levels as nominally corresponding to that standard’s Levels A, B and C.

What FADGI recommends

The guidelines give a direct recommendation that settles most arguments. To avoid rescanning, FADGI “does not recommend digitization to less than a three-star level when possible, and cautions against imaging to four-star level for all but the most sophisticated imaging programs.”

There is a nuance worth knowing. The same section says four-star “is an appropriate goal for smaller scope projects as it tends to be more achievable.” A few dozen hand-colored maps can reasonably aim higher than a long run of county deed books.

FADGI also draws its outer boundaries. It gives no recommendations below one star or above four. It notes that imaging beyond four-star may suit special uses, for example “when attempting to identify small before/after treatment differences in conservation.”

Why a ppi setting is not a star rating

Sampling frequency is only one of about a dozen parameters, and a high ppi setting can sit on top of a soft, noisy or over-sharpened image. The federal digitization rule says this in so many words.

Under 36 CFR 1236.46, a federal agency “cannot rely solely on equipment specifications, such as scanner ppi settings or camera sensor megapixels, to ensure digital image quality.” The rule’s photo and fine-detail section adds that “for many imaging devices, increasing the ppi settings may not increase the actual resolution level or capture the desired detail.”

Sampling is not resolution

Sampling frequency is the pixel count per inch of the original. Resolution, in FADGI’s sense, is how much real detail those pixels carry. The gap between the two is what the spatial frequency response (SFR) measures.

FADGI gives a worked example. An image captured at 400 ppi has a half-sampling (Nyquist) frequency of 200 cycles per inch, because it takes two pixels to define a cycle. If the SFR curve falls to 10 percent modulation at 180, the sampling efficiency is 90 percent, comfortably above the three-star floor of more than 80 percent.

For example, suppose a second scan of the same letter, also saved at 400 ppi, falls to 10 percent at 110 cycles per inch. Its sampling efficiency is 55 percent, below even the one-star floor of 60 percent for general documents. The two files have the same pixel dimensions and the same size on disk.

Sharpening and noise are capped in both directions

Sharpening can make a soft image look crisp without adding detail. FADGI measures it as the maximum of the SFR curve; a value above 1.0 “can be an indication of digital enhancement filtering.” Because “sharpening is irreversible,” the guidelines advise limiting it on archival masters.

Noise has an upper limit and a warning floor. A noise value below 0.25 suggests aggressive de-noising, which can remove “the texture or tooth in parchment or textured papers.” A file that looks too clean may have lost evidence about the paper.

Pixels on the sensor are not detail in the file

Cameras add their own limits. FADGI notes that color filter patterns on camera sensors mean “the true resolution is less than the stated resolution.” It also warns that lens quality can cap a system, so “more pixels on the sensor may not relate to increased resolution in the digital file.” Only a measured target shows what a given lens, sensor and setting deliver together.

Upsampling and automatic settings

Two shortcuts make a file look compliant without making it better. The first is upsampling: enlarging a lower-resolution capture to reach a required ppi. The federal rule’s file format section, in its paragraph on photographic prints, says agencies “must not transcode, or interpolate (upsample) files anywhere in the workflow.”

The second is automatic correction. The same rule requires settings during capture to match the settings used to evaluate the target, and says to “turn off auto correction settings in the capture equipment such as ‘auto exposure’.” FADGI’s own advice on adjusting files is shorter: “Do not rely on ‘auto correct’ features.” An image adjusted automatically, frame by frame, is no longer measured by the target that was shot at the start.

Is there such a thing as a FADGI-certified scanner?

No. FADGI’s technical guidelines resources page states plainly that it “does not approve, certify, or endorse commercial products,” and conformance belongs to a whole digitization program rather than to a device.

Conformance is a program, not a product

The guidelines list four components of a FADGI-compliant program. They are the technical guidelines and imaging parameters, documented best practices, digital imaging conformance evaluation, and professional staff. On the last point the text is blunt: “No claim of FADGI conformance can be made for programs that do not have appropriately trained staff and do not provide ongoing staff professional development.”

FADGI’s code of ethics for its Still Image Working Group adds the documentation test. “To be considered FADGI compliant, a digital imaging process must implement a digital imaging conformance evaluation program, and compliance should be demonstrated in project documentation or metadata.”

The same model can perform differently

Performance is measured per setup and per session because it changes. The guidelines note that “the performance of different units of the same model scanner/camera will vary,” and that performance “can change dramatically” after a software or driver update. They recommend testing at the start of each workday or batch, whichever comes first.

They also give buyers a direct instruction. “Ask manufacturers and vendors for actual test results, rather than relying on the specifications provided in product literature, as performance claims in product literature are often overstated.”

How to read the marketing

Phrase you may see What it can honestly mean What to ask for
“FADGI-certified scanner” Nothing official; FADGI certifies no products Target reports from sessions on your originals
“Four-star capable” A test once reached four-star under some conditions The category, settings, software and date of that test
“Scans at 1,200 ppi” A sampling setting Measured SFR10 and SFR50 at that setting
“FADGI-compliant workflow” A claim about a whole program Its conformance evaluation records and staff training

None of this makes equipment irrelevant. A good copy stand or book scanner makes three-star easier to reach every day. The point is that the star level is earned by the session, and the session report is the evidence.

What a star rating does not tell you

A star rating describes the image of a target, so it says nothing about how the original was handled, whether every page was captured or whether the files can be found again. A specification needs separate requirements for each of those.

Whether the original was handled safely

The notes for nearly every material category in the guidelines end with the same instruction: “In any situation where there is potential harm to the original, stop immediately and seek assistance.” A perfect target report can sit beside a cracked spine or a torn foldout. Handling rules belong in the specification next to the star level, along with who decides when to stop.

Whether the capture is complete and in order

FADGI’s inspection list includes completeness. It asks you to “verify that 100% of the source materials have been captured and accounted for,” and that “the digitized records are in the same order as the original.” Missing pages, skipped backs of photographs and shuffled folders are the defects researchers notice first, and no target measures them.

Whether the master is faithful

FADGI’s code of ethics asks that digitized material “document the appearance of the original at the time of capture, not what it may once have looked like if restored to its original condition.” It lists enhancements to avoid on masters, including colorization, digital infill, over-sharpening and the “removal of blemishes in the original such as stains, dust, or scratches.” Retouching belongs on access copies, and the guidelines ask that any special processing be documented.

Whether the files can be found and trusted

The guidelines go further than many buyers expect: “we do not consider an image to be of high quality unless metadata is associated with the file.” File names, embedded technical metadata and descriptive records are separate deliverables. FADGI also recommends validating file formats with a tool such as JHOVE as part of inspection.

Which star level for each kind of material

Start from three-star for anything you will keep as a preservation master, pick the FADGI category that matches the original, and move up or down only for a stated reason. The table gives the minimum sampling rates from the third edition, with a suggested starting level.

Original FADGI category Two-star Three-star Four-star Suggested start
Letters, diaries, manuscripts, carbon copies 3.3 Unbound, rare and special 250 ppi 300 ppi 400 ppi Three-star
Loose printed and typed papers 3.4 Unbound, general 250 ppi 300 ppi 400 ppi Three-star
Ledgers, registers, scrapbooks 3.1 Bound, rare and special 250 ppi 300 ppi 400 ppi Three-star
Printed books in good condition 3.2 Bound, general 250 ppi 300 ppi 400 ppi Three-star
Newspapers 3.7 Newspapers 250 ppi 300 ppi 400 ppi Three-star
Maps, plans, posters 3.6 Oversize 250 ppi 300 ppi 400 ppi Three-star, more ppi for fine engraving
Photographic prints, cabinet cards 3.8 Prints and photographs 250 ppi 400 ppi 600 ppi Three-star
Negatives, 35mm up to 4x5 in 3.11 Negatives 2,000 ppi 3,000 ppi 4,000 ppi Three-star
Negatives, 4x5 in and larger 3.12 Negatives 1,000 ppi 1,500 ppi 2,000 ppi Three-star
Slides and transparencies up to 4x5 in 3.9 Transparencies 2,000 ppi 3,000 ppi 4,000 ppi Three-star

Each figure carries a small tolerance in the guidelines, for example “300 ppi minus 2%.” Sampling is measured on the original, which is why film needs far higher numbers than paper. The scanning resolution calculator turns any of these rates into pixel dimensions and file sizes for your own originals.

Paper: letters, documents and newspapers

FADGI separates rare and special documents from general ones. Its rare and special category names manuscripts and “documents with poor legibility or diffuse characters, e.g., carbon copies, Thermofax.” Most unique handwritten papers in a historical society fit there better than in the general category. Unlike the general category, it has no one-star level to fall back on.

The guidelines list pass-through and automatically fed document scanners as not recommended for general unbound documents, because they “often introduce streak artifacts.” For rare and special documents, sheet-fed systems are listed as not recommended outright. Our document scanning page describes hand capture for this kind of material.

Rare and special, or general?

The category choice changes the notes that apply, not just the numbers. A simple decision rule for a mixed collection:

  1. If the item is unique, handwritten, carbon-copied or hard to read, use a rare and special category (3.1 or 3.3).
  2. If it is fragile enough that glass or a vacuum board could harm it, use a rare and special category, whose notes restrict both.
  3. If it is a printed or typed item that exists in other copies and handles easily, a general category (3.2 or 3.4) fits.
  4. If you are unsure, choose rare and special. The sampling rates are the same at two, three and four stars; the differences are in bit depth, color mode and handling notes, plus the missing one-star option.

Bound volumes

Bound volumes have their own two categories, 3.1 and 3.2, and both list flatbed scanners as not recommended. The notes say bound materials “must not be opened beyond the point where the binding is stressed,” even if that means a volume cannot be fully imaged with traditional techniques.

For the rare and special category, vacuum tables are also listed as not recommended, and glass contact needs approval and assistance. How to cradle ledgers, registers and scrapbooks safely is the subject of our companion article on scanning bound volumes without damaging the binding.

Photographs, negatives and slides

Prints follow category 3.8. FADGI asks that master files from color and black-and-white originals alike be “imaged in 16-bit color at or above 3-star performance,” because tone and surface differences are part of a photograph’s character. Flatbeds are allowed for prints, but dust removal on master images is not.

Film and glass are transmissive: they are read with light passing through them. FADGI calls its transmissive tone and color values “provisional,” and the federal digitization rule does not cover negatives or transparencies at all. Our photo and negative scanning page explains how film is captured as a negative master and inverted separately.

Maps and oversize sheets

Oversize items follow category 3.6. The guidelines note that “very fine detailed engravings, for example, may require 800 ppi or higher,” and that large originals at high ppi can exceed the TIFF file size limit, in which case a tile set is acceptable. Tiles and stitching raise their own questions, covered in our article on digitizing oversize maps and drawings.

Which star level for each purpose: access, preservation or replacement

Purpose moves the level more than material does. Access-only copies can sit at two-star, preservation masters belong at three-star, and scans that are meant to replace paper should meet a published three-star specification.

FADGI has framed specifications around use for a long time. Its 2009 working paper on content categories and digitization objectives states that guidelines “should be based on clearly articulated objectives describing the expected uses of the digitized content.” The 2023 edition repeats the idea: “for access only images, the expectation demands for image ‘goodness’ will not be as high as a collection being digitized to FADGI 4* criteria.”

Access and reference copies

If the images exist only so staff can find and pull the original, one or two stars can be enough. The risk is that access-only images become the only images, and then someone wants them for an exhibit or a book. FADGI’s advice to avoid future rescanning is the reason to choose three-star whenever the budget allows.

When two-star is a reasonable choice

Two-star is not a failure. FADGI calls it appropriate “where there is no reasonable expectation of having the capability to achieve three-star conformance, or when three-star conformance is not needed for the intended use.”

The guidelines are realistic about small programs. They describe a minimal setup as “a flatbed scanner and a single operator working with free software on a single computer,” costing a few hundred dollars, and say small projects with basic tools “should easily achieve FADGI level 2, and may achieve higher FADGI levels.” A volunteer team scanning donated snapshots for a reference database is a fair case for two-star, provided the specification says so in writing.

Preservation masters

When the originals stay in the collection but the files are meant to last, three-star is the default. Consider four-star for small sets where color itself is the evidence: hand-colored maps, watercolors, textiles in a catalog photograph, or documentation before conservation treatment.

Text recognition is another reason to hold three-star. FADGI says three-star imaging “generally produces image files capable of high quality conversion” for optical character recognition, while advising tests on your own material. The text recognition page explains how accuracy is measured on a sample.

Scans that will replace the originals

When paper may be disposed of after scanning, the bar should be a written, published specification. For federal agencies it is law. The federal digitization rule, published in the Federal Register on May 4, 2023, states that its image quality parameters “are based on FADGI three-star aim points and tolerance ranges.”

It sets 300 ppi for modern textual records and 400 ppi for photographic prints and records with fine detail. Once digitized records are validated, an agency disposes of the source records under its records schedule, unless it has reasons to keep them. The rule binds federal agencies only, so a county or museum should follow its own state archives’ guidance before discarding anything.

The National Archives’ 2004 guidelines are a useful contrast. They state that they “are not considered appropriate for preservation reformatting to create surrogates that will replace original records.” Specifications written from older documents may be aiming at access, not replacement.

Color targets, ISO 19264 and what actually gets measured

Every star claim rests on a known target captured under the same conditions as the originals and analyzed by software. If the target is wrong, dirty or out of date, the rating means nothing.

ISO 19264 and FADGI

ISO 19264-1:2021 defines image quality analysis for reflective originals in three levels. FADGI describes itself as being “in full alignment” with the ISO working group, and says any targets and software may be used in a FADGI-conforming process “if they meet the ISO 19264 standard and can provide all of the analysis functions required by FADGI.”

FADGI also refines the ISO approach. Its tables weight parameters differently by content type and “may not measure some of the parameters at all,” which takes into account the material and the intended use of the images. A ledger and a watercolor are judged on different terms.

Two kinds of target in practice

FADGI’s example workflows show two uses of targets, and a good specification names both:

  1. A device target, once per session. Imaged at the start of every session, and again after a break or a change of settings, to measure the equipment. FADGI says the target “should be checked and verified as passing prior to beginning imaging.”
  2. A small target in each frame. Placed beside the original, it records the conditions of that exact capture. FADGI’s recommendation is to include, at a minimum, “a gray scale, color reference, and an accurate dimensional scale” in each image.

Placement matters. For a page in a thick book, the target sits at the same height as the page. If the original is under glass, the target goes under the glass too; if the original is in a polyester sleeve, so is the target.

Targets wear out

FADGI asks that tone and color targets be “replaced on a routine basis,” because they collect dirt and scratches. It also notes that targets with few patches show consistency but cannot build color profiles, while targets with 100 or more patches give better input for ICC profiles. Color accuracy, the guidelines remind us, “is measured against the color test target, not the artifact.”

Software and film

FADGI lists both free and commercial analysis software. Its own OpenDICE program, developed at the Library of Congress, is free; as of October 2026 FADGI has paused direct technical support for it while it reevaluates the program. The OpenDICE page adds a caution that applies to every tool: results “are only as valid as the input measurements from the targets used.”

Film is harder to measure. FADGI notes that for transmissive work “only B&W targets are currently available for analysis,” and that negatives lack calibration targets, so settings may need adjusting frame by frame.

What a vendor’s target-analysis report should contain

A report you can act on names the FADGI category and star level, identifies the target, software and session, and lists every required parameter with its measured value and a pass or fail. Without those items, a star claim cannot be checked.

Ask for these elements for every session:

  1. The FADGI category and star level the session was meant to meet, for example “3.1, three-star.”
  2. The device, lens and capture software, with versions, because results change after updates.
  3. The target used and the reference data file it was measured against.
  4. The analysis software and version.
  5. The date and time of each target capture, including captures after breaks or setting changes.
  6. Each required parameter, its measured value, the tolerance and pass or fail.
  7. What was done about any failure, and the re-test that followed.
  8. The resolution written in each master file’s header, since a file without it fails reproduction scale accuracy.

Example (fictional). The Aster County Historical Society specifies FADGI category 3.1, three-star, for the Wren Gulch Mercantile day book in Box 3, a 212-page ledger whose split spine opens safely to about 110 degrees. The morning target for the second capture session returns these values against the three-star limits:

Parameter Measured Three-star limit Result
Tone response, ΔL*2000 1.8 under 3 Pass
White balance, ΔE(a*b*) 1.2 under 4 Pass
Lightness uniformity 1.6% under 3% Pass
Mean color accuracy, ΔE2000 2.1 under 3.5 Pass
SFR10 88% over 80% Pass
Sharpening 1.08 under 1.05 Fail
Noise 0.9 under 2 Pass

The sharpening value would pass at two-star (under 1.1) but not at three-star. The technician turns off capture sharpening in the camera software, re-shoots the target, and gets 1.01. Only then do the ledger pages go on the cradle, and both target reports go into the capture log for the box.

Inspection after capture

Target reports show the setup worked; inspection shows the files are complete. FADGI recommends visually inspecting “at a minimum, 10 images or 10 % of each batch,” whichever is larger, at 100 percent magnification. If more than 1 percent of the sample is defective, the whole batch should be re-inspected.

Our image QC checklist covers the visual checks, and the QC sample size calculator works out a statistically based sample if you prefer that to the 10 percent rule.

How to put star levels into your scanning specification

Write the level per series, tie it to a FADGI category and a purpose, and require the evidence. A one-line “scan to FADGI 4-star” for a whole collection is both more expensive than it needs to be and harder to check.

File size is part of the decision

Higher levels cost storage as well as capture time. For general documents, three-star allows 8-bit color while four-star requires 16-bit, and the sampling rate rises from 300 to 400 ppi. The arithmetic for one letter-size page in color:

Level Pixels Bit depth Uncompressed size
Three-star, 300 ppi 2,550 × 3,300 8 bits per channel about 25.2 MB
Four-star, 400 ppi 3,400 × 4,400 16 bits per channel about 89.8 MB

That is about three and a half times the storage per page before compression. The storage calculator carries that difference across a whole collection and its backup copies.

Example (fictional). The Aster County Historical Society wants Box 3 for an exhibit on Wren Gulch in the 1890s and for family research, so every series is a preservation master. Its specification reads, series by series:

Series FADGI category Level Minimum sampling
Okerlund letters and envelopes 3.3 Unbound, rare and special Three-star 300 ppi; 400 ppi for pages in pencil
Cabinet cards, front and back 3.8 Prints and photographs Three-star 400 ppi, 16-bit color
Wren Gulch Mercantile day book 3.1 Bound, rare and special Three-star 300 ppi, opened no more than about 110 degrees
Courier clippings 3.7 Newspapers Three-star 300 ppi

Below the table, one sentence sets the evidence: a device target at the start of each session and after every break, with the analysis report delivered alongside the files for that session.

A specification checklist

  1. List each series by FADGI category, using an inventory such as our collection inventory worksheet.
  2. Choose a star level for each series and write down the purpose behind it: access, preservation master or replacement.
  3. State the sampling rate as a minimum and the star level as a measured result, not a setting.
  4. Require a device target at the start of each session and after any change, with a written report.
  5. Require a target in each frame where the category calls for it, and say whether access copies may crop it out.
  6. Require the session reports to be delivered with the files and linked to them by date and batch.
  7. Set the inspection sample and the re-inspection trigger before capture begins.
  8. Run a small first batch and read the reports before approving the rest.

If you are drafting a request for proposals, our guide to writing a digitization RFP shows where this language goes, and the vendor selection checklist lists the questions to ask alongside it.

Dastok is a Colorado Springs company that digitizes historical documents, photographs and museum collections. We capture to the level agreed in writing and check each session against targets, and a pilot box is a way to see those target reports on your own originals before you commit a whole collection.

Working through this with a real collection?

If this article describes a decision you are facing, tell us about the collection. A pilot box answers most questions with your own material.

Plan a pilot box

Studio and contacts

24 South Weber Street, Suite 225
Colorado Springs, CO 80903
(719) 244-8450sales@dastok.com