Digitize large maps and drawings on equipment that holds the whole sheet still: a flatbed or planetary scanner with a bed at least as large as the sheet, or an overhead camera. Do not feed anything fragile, mounted, cloth-backed or of value through a sheet-fed scanner. Capture the sheet in one image when that delivers the resolution you need, and in overlapping tiles stitched in software when it does not, keeping the tiles as the archival master. Before any of that, a conservator decides whether rolled, folded or brittle sheets can be opened at all.
This guide turns the federal and conservation guidance on oversize originals into decisions you can make sheet by sheet. It covers which originals cause trouble, when sheet-fed scanning is unsafe, how to prepare rolled and folded sheets, the three capture methods, the arithmetic that decides between one capture and stitching, how to check seams, and how to store, name and describe files that can outgrow the TIFF format. Resolution levels are explained in more depth in our article on FADGI star ratings.
A note on interest. Dastok is a Colorado Springs firm that digitizes historical documents, photographs and museum collections, including large-format scanning of maps and drawings. The guidance below comes from the published sources cited where it is used, not from our own projects.
What makes maps and drawings hard to digitize
Oversize originals are hard because of their size, their handling history and their materials. Each one has to be supported over its whole area, many have been rolled or folded for decades, and several kinds of architectural print are sensitive to light, moisture or alkaline materials.
The Preservation Self-Assessment Program at the University of Illinois defines oversize as items that “do not easily fit into the common folder, archival box, or container without being rolled, folded, or placed flat in a file cabinet.” Its guide to architectural drawing reproductions notes that before the 1870s, copies of technical drawings “were produced by hand using translucent tracing paper or drafting cloth,” and that blueprinting reached North American architects and engineers in the mid-1870s, followed by many other light-sensitive copying processes.
Identify what you have before you plan the capture. The table summarizes what the Illinois guide and the Northeast Document Conservation Center (NEDCC) say about the materials you are most likely to meet.
| Original | What to know before capture | Source |
|---|---|---|
| Blueprint (cyanotype), about 1872 onward; technical use mostly to the 1950s | “Very sensitive to light but are otherwise quite stable if kept in dark storage”; keep away from alkaline materials; paper distortion from the wet process is common | PSAP |
| Diazo print, 1923 onward | “Very sensitive to light,” though less so than cyanotypes; often brittle from residual chemicals; may smell of ammonia; “should be assumed fragile and volatile” | PSAP |
| Sepia diazo intermediates | May carry a wax, paraffin or oil coating added for translucency | PSAP |
| Tracing paper drawings and plans | Thin and often acidic; the Library of Congress lists some tracing paper drawings among items that may be excluded from digitization | LoC |
| Maps and posters on thin paper backed with linen or muslin | Historically backed with woven fabric for support; the backing may itself be failing | NEDCC 7.5 |
| Wall maps on wooden rods | Often varnished, “dark and brittle,” with failing mounts | NEDCC 4.9 |
| Encapsulated sheets | Housed in polyester film; positioning matters to avoid glare and reflections; once encapsulated, a sheet “can never be rolled” | FADGI, NEDCC 4.9 |
One more warning from the Illinois guide matters for cataloging: a date on a print may be the date of the original drawing, not of the print. Record what you see and where you saw it.
When a sheet-fed scanner is unsafe
A sheet-fed scanner pulls the original between rollers past a fixed sensor. For oversize cultural heritage material, the federal guidelines and the Library of Congress both say not to use one, for reasons of image quality and of safety.
The FADGI Technical Guidelines (third edition, 2023) cover maps and posters in section 3.6, “Oversize Items: Maps, Posters, and Other Materials.” They recommend planetary scanners, digital cameras and flatbed scanners, and list “pass through manual or automatically fed document scanners” as not recommended, because this class of equipment “often introduces streak artifacts in the imaging process, which are not FADGI compliant.”
The Library of Congress is blunter about safety. Its Preservation Guidelines for Digitizing Library Materials state that “form feed equipment is not acceptable for scanning fragile, high-value, fine art, or special or archival collection materials including drawings, graphic prints, manuscripts, newsprint, photographs; and equivalent materials.” They add that oversized materials “must be scanned using equipment that features a scanning bed that is as large or larger than the object to be scanned.”
FADGI does list sheet-fed scanners as acceptable in one place: its category for modern textual records, written for routine federal paper records. Even there, it says those specifications do not apply to records that “include fine detail” or need high color or tonal accuracy. A historic plat or an architect’s drawing is not that kind of record.
A decision rule
Keep a sheet off any feeder if any of these is true:
- It is brittle, torn, creased or missing pieces. The Library of Congress flags tears longer than a quarter inch as a condition problem.
- It is backed with cloth or board, mounted, hinged or encapsulated.
- It is tracing paper, drafting cloth, a coated print, or carries flaking or powdery media such as soft pencil, chalk or crayon.
- It has seals, ribbons or anything else attached.
- It has artifactual or legal value as an original, or you have not decided yet whether it does.
What remains is usually modern duplicate prints in sound condition, kept only for their information. Whether to risk them on a feeder is your decision, and the streak artifacts still count against image quality.
Preparing rolled, folded and cloth-backed sheets
Preparation decides whether a sheet can be captured safely at all. The rule is simple: never force a rolled or folded sheet flat. If it resists, relaxing it is conservation treatment, done by a conservator, before capture.
Rolled sheets
NEDCC’s leaflet on storage solutions for oversized paper artifacts is direct: “Many collections contain objects that have been rolled for years and are too brittle to unroll safely.” Such items “should be forwarded to a conservator for humidification and flattening,” and until then they should be wrapped, stored horizontally and “put off-limits to researchers.” The same caution applies to a digitization queue.
A practical test is to unroll a few inches with the roll supported on the table. If the paper cracks, flakes or springs back hard, stop. NEDCC’s leaflet on conservation treatment for works on paper describes flattening “between blotters or felts under moderate pressure after the object has been delicately humidified and relaxed,” and notes that “all media must be carefully tested beforehand for water sensitivity.” That testing is why humidification is not a task for a scanning station: inks, colored media and coatings vary, and only testing shows which of them tolerate moisture.
Folded sheets
“Folding damages paper and is not recommended,” says NEDCC, and with age folded sheets “may become brittle and resist unfolding, so that they could break in the process.” Its advice is to unfold cautiously, to bring resistant sheets to a conservator, and not to “unfold oversize objects until you have figured out how to store them afterward.” If a folded map cannot be opened safely, capture it folded, panel by panel, and record that in the capture log.
Cloth-backed and mounted sheets
Maps and posters on thin paper were often backed with linen or muslin. NEDCC notes that old wall maps “were customarily backed with cloth, attached to wooden rods at the top and bottom edges,” varnished, and are now often dark and brittle with failing mounts. A cloth backing makes a sheet feel strong when it is not. The paper on the front can still crack along old fold lines, and a varnished surface reflects light unevenly.
The Library of Congress lists the stabilization a conservator may do before capture: “opening of folds or creases that obscure text or images,” “relaxing cockled or creased paper,” and “mending tears.” It also lists items that may be excluded altogether, including some tracing paper drawings and plans, paper with three-dimensional objects attached, and loose or flaking media. If you need a conservator, the American Institute for Conservation’s find a professional member directory lists peer-reviewed members.
Handling on the day
- Move large sheets on a rigid support, such as heavy board, and with two people. The Illinois guide recommends both, and FADGI’s example map workflow notes that some oversize items “need at least two people to handle the item.”
- Do not lay glass on a fragile sheet to flatten it. The Library of Congress warns that this “can cause media to crack or to detach from the item.”
- Keep weights on margins, never on drawn or printed content.
- Do not cut or section a map to fit equipment. NEDCC notes that “professional library and archives practice prohibits cutting up maps.”
Our condition assessment checklist records these findings sheet by sheet, and the packing and transport checklist covers moving rolls and flat sheets. How a studio should handle and log originals in its care is set out on our collection care page.
Example (fictional). The Aster County Historical Society finds a roll of three blueprints for an addition to the Wren Gulch school, the top sheet dated 1912 in its title block. Unrolled two inches on a padded table, the outer sheet cracks along an old crease. The roll goes back in its wrapper, marked off-limits, and onto the conservator’s list for humidification and flattening. The cataloger notes that the 1912 date may belong to the drawing rather than the print. The society’s hand-colored plat of the Wren Gulch townsite, folded in eight panels, opens without strain and goes ahead.
Three ways to capture a large sheet
FADGI describes three methods for large originals, says each has limits, and endorses none: “FADGI does not endorse any one of these approaches over another. Each has their appropriate use.” Choosing one is a matter of sheet size, the detail you need and how the original can safely lie.
| Method | How it works | Strength | Limit (in FADGI’s words or summary) |
|---|---|---|---|
| Single capture | The whole sheet in one image, usually with an overhead camera | Simple, fast, no seams | “Inadequate for larger originals” at high resolution |
| Linear scanning | The image is built one line at a time, as in a flatbed or a scanning back | Higher resolution than one capture | “Limited by the size of the sensor and/or available lenses” |
| Tiles and stitching | Overlapping sections captured and joined in software | “No limitation to resolution or original size” except the file format | “Loss of geometric accuracy and resolution inherent in acquiring images in sections” |
All three can do good or poor work. FADGI warns that geometric accuracy “can vary dramatically based on the approach taken and the specific imaging systems used,” and that “all three can produce highly accurate images, and all three can deliver poor accuracy.”
Matching the method to the original
The condition of the sheet often narrows the choice before resolution does:
- Flat, sound sheets that fit the bed. A large flatbed or planetary scanner works, provided nothing presses on the surface beyond what the sheet tolerates.
- Sheets that will not lie flat. Cockled paper, cloth-backed maps that undulate and varnished wall maps are better captured from above with a camera, supported on the table, with nothing pressing on them.
- Encapsulated sheets. NEDCC explains that encapsulation edges are sealed “with ultrasonic welding equipment or with a heat welder,” so taking a sheet out means cutting the film. FADGI’s map workflow notes that some housed items are “too fragile to remove from the housing,” which then “determines how the items need to be scanned in order to avoid unnecessary reflections and distortions.” Decide with a conservator, and if you capture through the film, light it to avoid glare.
- Glossy or varnished surfaces. FADGI’s glossary defines specular reflection as light reflected “off a shiny, glossy or mirror-like surface.” Its example workflows group reflective items that “need special lighting set-ups to avoid glare,” which is a sensible way to schedule varnished maps.
- Folded sheets that cannot open. Capture panel by panel as the sheet lies, and record it.
FADGI’s oversize category allows grayscale or color capture at every star level and offers no bitonal (pure black-and-white) option. Even a crisp modern drawing is captured in tones, which keeps faint pencil notes, erasures and stamps.
Two rules apply whichever you choose. FADGI lists as not recommended any lighting that raises the surface temperature of the original by more than 4 degrees F (2 degrees C) over the whole imaging process. And it closes its oversize notes with the instruction every operator should know by heart: “In any situation where there is potential harm to the original, stop immediately and seek assistance.”
Single capture or stitching: working out the pixels
Choose single capture when the sensor holds enough pixels to cover the whole sheet, plus a margin, at the resolution you specified. When it does not, stitch tiles or use a linear scanner. The arithmetic takes a minute per sheet size.
The resolution you need
FADGI’s oversize category sets minimum sampling rates by star level: 200 ppi at one star, 250 at two, 300 at three and 400 at four, each with a small tolerance (300 ppi at three stars means at least 294 ppi). It adds that resolutions above 400 ppi “may be appropriate for some materials,” and that “very fine detailed engravings, for example, may require 800 ppi or higher.” For a plat with lot numbers written in a fine hand, or an engraved county map, plan on 400 ppi and test whether more shows anything new.
The pixels a sheet needs
Multiply each dimension in inches by the ppi. A 24 by 36 inch drawing at 300 ppi needs 7,200 by 10,800 pixels; at 400 ppi it needs 9,600 by 14,400. Then compare both dimensions with the sensor, leaving room for a margin around the sheet and any target in frame.
For example, suppose a camera sensor delivers 11,000 by 8,000 pixels. At 300 ppi it can cover at most 36.7 by 26.7 inches, so a 24 by 36 inch drawing (7,200 by 10,800 pixels) fits in one capture, with a little room for a margin. At 400 ppi the same sensor covers at most 27.5 by 20 inches, so the same drawing needs tiles or a linear scan. Megapixels alone can mislead: a long, narrow survey plat may fit the megapixel count and still fail on its long side.
Example (fictional). The Aster County Historical Society’s hand-colored plat of the Wren Gulch townsite measures about 30 by 40 inches, and its lot numbers are written in a fine hand, so the society specifies 400 ppi. The plat needs 12,000 by 16,000 pixels, 192 megapixels. Suppose the camera is the hypothetical 11,000 by 8,000 pixel one above. At 400 ppi each capture covers 27.5 by 20 inches; with 20 percent overlap, each new tile advances 22 by 16 inches. Two rows of two tiles cover 49.5 by 36 inches, enough for the plat and a margin, so four tiles is the minimum. A provider may choose more, smaller tiles, and the specification should say who decides.
Lens and evenness
Pixel count is not the only limit. FADGI’s section on stitching notes that “lenses have limited resolving capability when tasked with imaging very large and detailed materials like maps.” Light must also be even across the whole sheet, which gets harder as the sheet grows. A single capture that meets the pixel count but fails FADGI’s sharpness or uniformity measures on a target is still a failed capture. The scanning resolution calculator does the pixel and file size arithmetic for your own sheet sizes.
How to stitch well and check the seams
Stitching works when every tile is captured under identical conditions with generous overlap, the tile set is kept as the archival master, and every seam is checked against the original’s own straight lines and scale. Done carelessly, it produces doubled text, broken lines and a map whose measurements are wrong.
Capture rules for tiles
FADGI’s section 6.5 on stitching sets the conditions. The technique “requires stability of all elements of the imaging system including even lighting, precise movement and positioning of the image between segments, and consistent exposure.” Tiles “should be captured with overlap to ensure stitching is possible and no content is lost. Best practice is to capture 20% overlap between adjoining images.”
Which file is the master
FADGI is clear on this, and it matters for preservation. “When using stitching, the set of individual stitches should be considered the archival master. The assembled version is considered the production master.” Its oversize notes repeat the point: the group of tile files “as a whole is considered the archival master file,” and “a folder containing all files should be retained for archival purposes.” Keep the tiles even after a stitch looks perfect. If a better stitching program appears, or a seam error is found years later, the tiles let you redo the work without handling the original again.
Checking the seams
FADGI’s glossary admits that aligning the tiles accurately into one uniform image “is technically complex and challenging.” Check every seam at full size, not on a screen-sized preview:
- Straight lines. Follow borders, neat lines, graticules, section lines, property lines and dimension lines across each seam. They should continue without a step, kink or gap.
- Text across seams. Look for doubled letters, ghosted strokes or missing characters where lettering crosses a join.
- Tone and color. A visible band or a shift in paper tone at a seam means exposure or lighting changed between tiles.
- Scale. Measure a known distance that crosses one or more seams, such as the map’s own scale bar or a ruler placed in frame, and compare it with the resolution recorded in the file. FADGI’s reproduction scale accuracy limits for oversize items are within 2 percent at three stars and within 1 percent at four stars.
- Completeness. Confirm that the whole sheet, edges included, appears in the stitched image, with nothing lost in an overlap.
Example (fictional). The stitched master of the Wren Gulch townsite plat is captured at 400 ppi. The surveyor’s printed scale bar, 10 inches long, crosses one vertical seam, so on the image it should measure 4,000 pixels. It measures 3,930, which is 1.75 percent short. That passes FADGI’s three-star limit of 2 percent and fails the four-star limit of 1 percent, which the society had specified. The checker finds a one-tile misalignment at the seam, the plat is restitched from the kept tiles, and the bar then measures 3,992 pixels, 0.2 percent short. Nobody had to handle the plat again.
Record each failed seam with the tile numbers, recapture or restitch, and keep the record with the files. The image QC checklist covers the general checks that apply to every capture.
Scale, color and light during capture
Every master of a map or drawing should show the whole sheet with a small margin, carry its true resolution in the file header, and be captured with a color target under the same light, with exposure kept short for light-sensitive prints.
FADGI’s notes for oversize items ask that master files include “the entire area of the original and a small amount beyond to define the area,” and that any backing color “extend beyond the original” without being used to set tones. Its section on reproduction scale accuracy explains why the recorded resolution matters: “capturing an image of a ruler at 400 ppi will digitally render the ruler at the correct size when displayed or printed at 400 ppi.” It is strict about the header value: “If this information is missing from the header of the image file, the image is not FADGI compliant.” For maps, where people will measure distances, a physical scale bar in the session’s reference frame gives a check that does not depend on metadata.
For color, FADGI’s example workflow for a map collection places “small targets” in each unprocessed scan “to monitor and track the color accuracy of each image,” cropped from the final image, and scans a separate device target once a day. Capture blueprints and diazo prints in color, even when the drawing is monochrome. The blue of a cyanotype, the purple of a diazo and the brown of a sepia print are evidence of the process, and grayscale throws that evidence away.
Light deserves attention with these prints in particular. The Illinois guide calls both blueprints and diazos “very sensitive to light,” and the Library of Congress requires scanning equipment with “controls to limit light and heat exposure to the items being scanned.” Set up focus, exposure and tile positions on a stand-in sheet, then expose the original only for the captures themselves.
File formats and sizes for very large images
Large maps produce very large files. Plan the master format before capture: TIFF has a 4 GB ceiling, so the largest captures need a tile set, BigTIFF or lossless JPEG 2000.
FADGI’s oversize category lists TIFF and JPEG 2000 as master formats at every star level, with 8-bit color at one and two stars and 8 or 16 bits at three and four. It also warns that “large originals at high ppi resolutions will exceed the maximum file size allowed in the TIFF format,” and that “if necessary, saving the master file as a tile set is appropriate.”
The ceiling comes from the format itself. The Library of Congress’s format description for TIFF quotes the reason: offsets in standard TIFF are 32-bit numbers, so the largest is “2^32 bytes, or 4 GB” (about 4.29 billion bytes). Its entry for BigTIFF describes a variant that uses 64-bit offsets, “vastly transcending TIFF’s normal 4 GB limit,” and supports GeoTIFF metadata, useful if the maps will later be georeferenced. Check that your viewer, image server and preservation system read BigTIFF before you choose it.
The table shows uncompressed image data for color masters, computed as width × height × ppi² × bytes per pixel (3 bytes at 8 bits per channel, 6 at 16), in decimal units.
| Sheet | ppi | Pixels | 8-bit color | 16-bit color |
|---|---|---|---|---|
| 24 × 36 in | 400 | 9,600 × 14,400 (138 MP) | 415 MB | 829 MB |
| 30 × 40 in | 400 | 12,000 × 16,000 (192 MP) | 576 MB | 1.15 GB |
| 36 × 48 in | 400 | 14,400 × 19,200 (276 MP) | 829 MB | 1.66 GB |
| 36 × 48 in | 600 | 21,600 × 28,800 (622 MP) | 1.87 GB | 3.73 GB |
| 48 × 96 in | 400 | 19,200 × 38,400 (737 MP) | 2.21 GB | 4.42 GB, over the TIFF limit |
Lossless compression usually makes the files smaller, and the tile set adds overlap, so a stitched project can occupy well over the figure in the table. The storage calculator turns per-image sizes into terabytes across copies and years.
JPEG 2000 is the other route. The Library of Congress’s entry for JPEG 2000 core coding describes support for “images with large picture sizes, high spatial resolution, and high bit depth,” and its entry for lossless JP2 notes that lossy JP2 files “are being used for the service images of maps in loc.gov.” For access, very large images work best in a zooming viewer rather than as downloads; IIIF, covered in our collection search service, is an open standard for that.
Naming and describing multi-sheet sets
Every tile, sheet and set must be connected by file name and embedded metadata, so that the archival master can be reassembled and found without the person who made it. FADGI’s oversize notes require it: “If the image capture is made in sections, the files must be related by file naming and embedded metadata.”
FADGI’s example map workflow shows one way: because many items “cannot be scanned in one image, a grid pattern is determined and carried out with letter or character identifiers appended to the unprocessed filename.” Apply the same logic in three layers:
- The set: one identifier for the plan set, atlas or map series.
- The sheet: a sequence number in the set’s own order, such as sheet 3 of 12, matching the sheet numbers printed in the title blocks where they exist.
- The tile: a suffix in a fixed reading order, left to right and top to bottom.
Our file naming builder produces names in the pattern achs_c003_b03_f012_i004_0001_m.tif. For a plan set you might treat the set as the item and the sheet as the sequence number, then add a tile suffix: achs_c009_b01_f004_i002_0003_t05_m.tif for tile 5 of sheet 3, kept in a folder for that sheet’s tiles, with the stitched file named without the tile suffix. Whatever pattern you choose, write it down, keep the width fixed, and use it from the first sheet.
What to record in the description
- Sheet number and total, title, and any revision letters or dates in the title block.
- The kind of original: ink drawing on tracing cloth, blueprint, diazo, printed map, hand-colored manuscript plat.
- Dimensions of the sheet as measured, not as printed.
- Capture method (single, linear or tiled), number of tiles, resolution and the seam check result.
- Condition notes: folds captured in place, panels captured folded, conservation before capture.
County and municipal offices hold plats and plans among their permanent records; our page on local government records covers that kind of collection.
What drives cost, and what to ask a provider
The cost of digitizing oversize material depends on condition and handling, not only on sheet count. A per-sheet figure means little until someone has seen the sheets, so plan around the drivers instead:
- Condition and preparation. Rolled, folded, brittle or cloth-backed sheets may need a conservator before capture, which adds both cost and time.
- Handling. Two people, a rigid support and a slow pace for each large sheet.
- Resolution and size. Higher ppi and larger sheets mean more tiles; tile count multiplies capture, stitching and checking time.
- Seam checking and rework. Every seam is a place where a check can fail.
- Housings. Encapsulated sheets need careful positioning; FADGI’s map workflow notes items “housed in Mylar” positioned “to avoid glare and unwanted reflections.”
- Description. Sheet-level records for plan sets take longer than a single record for a map.
- Storage. Files of hundreds of megabytes to several gigabytes each, times the copies you keep.
Questions to put to a provider
Whether you outsource or equip your own station, the same questions expose most of the risk. Ask for the answers in writing, and ask to see them applied to a few of your own sheets:
- Which equipment will be used for each group of originals, and will any original go through a sheet-fed scanner?
- Is the scanning bed or copy table at least as large as your largest sheet, as the Library of Congress requires?
- How are light and heat exposure limited, and how is the 4 degrees F (2 degrees C) surface temperature limit checked?
- When is stitching used, with what overlap, and are the tile sets delivered as the archival master?
- How is every seam checked, and will each sheet’s scale accuracy be reported against the specified star level?
- Who decides that a sheet needs a conservator, and what happens to a sheet that resists opening on the day?
- Which master format will be used for files over 4 GB, and can your systems read it?
- What naming pattern and embedded metadata tie tiles, sheets and sets together?
Our large-format scanning page describes how we approach these questions.
For bound atlases and plat books, the cradle and opening-angle rules in scanning bound volumes without damaging the binding apply before any of this.
What to do next
A short sequence works for most map and drawing collections:
- Inventory the oversize material and identify each kind of original, using the table above.
- Run a condition check on every sheet, and set aside anything rolled tight, brittle, cloth-backed or folded that resists opening.
- Get a conservator’s view on the set-aside sheets before any capture date is fixed.
- Choose the resolution for each group, work out the pixels, and decide between single capture, linear scanning and tiles.
- Fix the master format (TIFF, BigTIFF, tile set or JPEG 2000) and the naming pattern before the first capture.
- Check every seam at full size, measure scale, and keep the tile sets.
If you want to see these decisions made on your own sheets before committing a whole map drawer, a pilot box runs a small batch of real originals through capture, stitching and checking, with the results reported before anything larger is decided.