Plan a pilot box
Menu

Scanning bound volumes without damaging the binding

Reader question: How do we digitize bound ledgers, registers, scrapbooks and books without forcing them flat or cutting them apart?

By Dastok Editorial TeamIssue: Published

To scan bound books without damaging them, open each volume only as far as its binding allows, support both boards in a cradle at that angle, and capture the pages from above with a camera or overhead book scanner instead of pressing the spine onto a flatbed. The Library of Congress teaches its own digitization technicians not to apply pressure to flatten books and to cradle volumes with weak joints or restricted openings. Fragile books do not need to be cut apart to be scanned. A volume that will not open far enough needs a narrower capture, a conservator’s help first, or a later date.

This article works through that rule for the bound formats common in small archives: ledgers, registers, letterpress copybooks, scrapbooks and older printed books. It covers a triage before capture, the equipment choices, tight gutters, foldouts, brittle paper and red rot, and the questions to ask anyone who will scan your volumes.

Why bound volumes get damaged during scanning

Bound volumes are damaged when they are opened wider than the binding allows, pressed flat, heated, or turned faster than brittle paper can bear. Most of that harm comes from equipment designed for loose sheets.

A flatbed scanner or photocopier is built for paper that lies flat on glass. A book does not, so the operator presses on the spine to get the gutter into focus. NEDCC’s leaflet on storage and handling describes the problem directly: “Photocopiers and flatbed scanners encourage users to press the binding flat in order to get a good image, and this damages the volume.”

The Library of Congress names the result. In its preservation guidelines for digitizing, it warns that pressure to flatten a book “can break the spine or loosen or break off brittle pages in a book.” The damage is cumulative: a joint that cracks during one scanning project is weaker for every reader after it.

Heat, light and speed

Capture lighting adds a second risk. The FADGI Technical Guidelines list as not recommended any lighting that raises the surface temperature of a rare or special bound volume by more than 4°F (2°C) over the whole imaging process, and more than 6°F (3°C) for general collections. The Library of Congress requires contractors’ equipment to “feature controls to limit light and heat exposure to the items being scanned.”

Speed is the third risk. Automated page turners have improved, and FADGI lists them among the technologies that can suit some projects, with a plain condition: “Do not use automatic book scanners that cause damage to collections materials.” For brittle or tightly bound volumes, hand turning is the safe default.

Sheet feeders and vacuum boards

Two other kinds of equipment need particular caution. NEDCC is categorical: “Historic documents and photographs should never be fed through a sheet-fed copier/scanner, as they may jam the machine and become damaged in the process.” The Library of Congress tells its contractors that form feed equipment “is not acceptable” for fragile, high-value, special or archival materials.

Vacuum tables hold sheets flat by drawing air through them. FADGI lists them as not recommended for rare and special bound volumes. For rare unbound documents it asks for a conservator’s approval first, because “air forced through the original over the vacuum ports can permanently degrade some originals.” A loose leaf that has fallen out of a ledger deserves the same caution as the ledger.

The handling rules the Library of Congress teaches its technicians

The Library of Congress trains its digitization technicians in five rules for bound materials: no pressure to flatten, cradles for weak or restricted bindings, extreme care with brittle paper, foldouts opened onto a support, and no glass laid on top of fragile items to flatten them. They work as a checklist for any scanning station.

The Library’s preservation staff teach these rules “with non-collection samples of bound materials, flat documents, graphic prints, manuscripts, atlases, photographs, and photograph albums to demonstrate the damage that can occur.” A volunteer program can copy that idea with discarded books before anyone touches a ledger.

Library of Congress rule What it means at the scanner
“Don’t apply pressure to books in order to flatten them for image capture.” No hands, weights or lids on the spine to close the gutter
“Place books with weak joints or restricted openings in a book cradle (blocks or rolls of polyethylene foam) during image capture.” Both boards supported at the angle the book opens to on its own
“Handle brittle paper with extreme care.” Pages turned by hand, one at a time, with a page turner if needed
“Don’t remove foldouts from books. Carefully open the foldout onto a support during image capture.” Foldouts captured in place, never cut or detached
“Don’t place glass or Plexiglas® on top of” artwork, documents, manuscripts, prints or photographs to flatten them Glass on pages only where the material and binding can take it, never on media that can crack or lift

The workspace

The same guidelines set out the workspace: a clean, roomy, tidy table; washed and dried hands; gloves when handling photographs; pencils only near collection materials; no food or drink; and books closed and covered when the operator steps away. FADGI adds that hand sanitizer should not be used before handling materials.

Gloves or clean hands

For paper, the Library of Congress guide to preserving your books says it “does not advocate for the use of gloves when handling paper-based collections material.” Gloves reduce touch, make page turning harder and can snag torn corners. Freshly washed and dried hands, without lotion, are the Library’s recommendation for books; gloves are for photographs.

Triage before you scan: binding type and condition

A short triage of each volume, before it reaches the scanner, decides how it can be captured: as is, with extra support, after a conservator stabilizes it, or not yet. Record the result in the inventory, so the scanning order can follow condition rather than shelf order.

The Library of Congress lists the condition problems its preservation staff look for in items selected for digitizing. For bound volumes, the most relevant are text obscured by folds or creases, tears longer than a quarter inch, “books with loose joints, detached spines, or boards,” and “restricted bindings that open less than 90 degrees.”

Measuring the safe opening angle

The safe opening angle is the widest the volume opens with its boards supported and no resistance at the spine. Find it by opening the book slowly on a padded surface, supporting each board with foam as it lowers, and stopping at the first resistance. Note the angle in the inventory in round numbers. The Library’s guide puts the principle simply: “Do not force a book to lie open completely flat; instead, prop up the covers of an opened book to decrease the opening angle.”

Pressed flat, 180° What flatbeds and copiers invite Pressure on the spine: avoid Book-edge scanner, 100° Book hangs over the scanner edge No more than about 100° Cradle at the safe angle, 110° Both boards supported, shot from above Foam wedges hold the angle Restricted, under 90° Flagged in condition review Each page captured on its own
Opening angles for bound volumes, seen from the side. The 100-degree figure is NEDCC's for book-edge scanners and the 90-degree threshold is the Library of Congress's for restricted bindings; the 110-degree cradle is the fictional Wren Gulch day book. Sources: NEDCC Preservation Leaflet 4.1 and Library of Congress, Preservation Guidelines for Digitizing Library Materials, checked November 2026.

A triage table

What you find What it means Capture route
Opens past 120° with no resistance, sound joints Flexible binding Cradle or overhead capture; standard handling
Opens between 90° and 120° Moderate restriction Cradle at the measured angle; check gutter reach on a test page
Opens less than 90° Restricted binding, flagged by the Library of Congress Cradle, each page captured on its own; decide in advance what gutter loss is acceptable
Loose joints, detached spine or boards Structure already failing Conservator stabilizes joints or boards first
Powdery leather that marks your hands (red rot) Leather deterioration Polyester film jacket for handling; severe cases wait for a conservator
Brittle pages that crack at the fold Paper failure Page turner, slow pace, stop at the first loss; may need treatment first
Tears longer than a quarter inch in the text area Risk of extending the tear Support the leaf; consider mending first
Iron gall ink that has eaten into the page Ink corrosion Conservator decision before handling

The 90-degree line and the conditions come from the Library of Congress; the 120-degree band is a practical working line, not a published standard. Our condition assessment checklist gives a printable version of these checks, including “how far the volume opens safely without strain.”

When the answer is a conservator

The Library of Congress describes stabilization as “minimal conservation treatment performed by conservators,” including opening folds, relaxing cockled paper, mending tears, repairing loose joints and reattaching loose spine pieces or boards. It also lists materials that “may be excluded from digitization,” among them “books with severe leather deterioration (i.e., red rot) or missing pages” and “paper with iron gall ink that has eaten into the page.” Exclusion there means a curator and preservation specialist talk first; it is not a judgment that the volume never gets scanned.

Capture options compared: cradle and camera, overhead scanner, flatbed

For bound volumes, capture from above while the book rests in a cradle: a camera on a copy stand or a planetary (overhead) book scanner. FADGI lists flatbed scanners as not recommended for both of its bound-volume categories.

What FADGI recommends

The third edition of the FADGI Technical Guidelines sorts equipment by category. For rare and special bound volumes (category 3.1), it recommends manually operated planetary book scanners and digital cameras with book cradles, either with or without glass or plastic platens, and automated page-turning scanners only where they do no damage. It lists as not recommended flatbed scanners, vacuum tables, and linear scanning backs, because of “the potential for the original to flex during the scanning process.”

For general bound volumes (3.2), planetary book scanners and digital cameras are recommended. Flatbed scanners remain not recommended, along with linear scanning without glass or plastic platens.

Method How the book sits Pressure on the spine FADGI status for bound volumes Best for
Camera on a copy stand with a cradle In a cradle at its safe angle None if the cradle fits Recommended (3.1, 3.2) Rare and fragile volumes, ledgers, scrapbooks
Planetary (overhead) book scanner On an adjustable cradle under the scan head Low; depends on platen use Recommended (3.1, 3.2) Steady runs of volumes in fair condition
Automated page-turning scanner Held open by the machine Varies by design Recommended only if it causes no damage Long runs of sturdy printed books
Book-edge flatbed Hangs over the scanner edge, about 100° Moderate Not listed separately; flatbeds not recommended Public self-service copying of sturdy books
Standard flatbed or copier Face down, pressed flat High Not recommended Loose sheets only

Why the camera must be square to the page

FADGI’s guidance on accessories says “an imaging system must be parallel at the sensor, lens, and object planes.” A page lying at an angle in a cradle is not parallel to a camera pointing straight down. The fix is to tilt the camera or the cradle so each page in turn faces the lens squarely, and to capture left and right pages separately when the opening is narrow.

The Library of Congress writes the same need into its contractor requirements: scanning equipment “must be adjustable to the height of the collection item to accommodate books that need cradle support.” A setup that cannot raise or tilt its camera will push operators to flatten the book instead.

Glass platens

Glass holds pages flat and removes curvature, and FADGI lists book scanners and cameras “with or without glass or plastic platens” among its recommended tools. For general bound volumes it permits glass contact, with a condition: “the binding of the book must not be stressed in the process.” For rare and special volumes, glass contact needs “appropriate approval and assistance.” FADGI warns that it can damage the original, which “is particularly true for pigmented and gold leaf materials.” Never lower glass onto a page with flaking media, raised seals or pasted-in items.

What NEDCC says about public copying

NEDCC’s leaflet speaks to reading rooms, and its numbers help when you choose equipment. “Overhead scanners are best for public use because they allow a book page to be copied with the book open less than 180 degrees.” Where no overhead scanner exists, NEDCC prefers copiers and flatbeds with a “book edge,” which “does not require the book to open more than 100 degrees,” over standard machines. The leaflet adds that the book-edge position gives “less distortion” and captures inner margins “more clearly.”

Setting up a safe capture station for bound volumes

A safe station is mostly preparation: a cradle that fits the volume, a camera that can meet each page squarely, tools within reach, and a routine that checks the setup before the first page. Most damage happens when the setup forces the operator to improvise.

What the station needs

FADGI suggests a basic tool kit at each imaging station: “gloves, spatulas, thin Mylar strips, weighted aids to hold materials down, foam ‘props’ and sheets with the ability to resize them as needed, lens wipes, air duster, soft brushes.” The Library of Congress guide adds snake weights; using them “helps to keep pages open with minimal pressure.” Add a padded surface larger than the largest volume, a pencil and the capture log.

Setting up for one volume

  1. Clean the cradle, platen and work surface before the session, as FADGI recommends for all equipment except lenses.
  2. Bring the volume to the station in its box and let it sit at room conditions if it came from colder or damper storage.
  3. Read its safe opening angle from the inventory, then set the cradle wedges to that angle with the volume closed beside it.
  4. Open the volume into the cradle, supporting each board as it lowers. Stop if the spine resists before the recorded angle.
  5. Adjust the camera height and tilt so the sensor is parallel to the first page, and place the target at the height of that page.
  6. Capture the target and check it against the agreed tolerances before any page is imaged.

The session routine

Turn each leaf by hand from the fore-edge, let it settle onto its foam support, and lay a snake weight only on the margin if the page lifts. Capture, check the frame on screen for focus into the gutter, then turn. When the text block shifts from one board to the other, adjust the wedges so the boards stay supported, and move the target to the new page height.

FADGI’s session rule applies to every break: “If the session is disrupted by a break, etc., the target should be re-imaged and checked and verified before resuming the session.” Close the book and cover it when you step away, as the Library of Congress asks.

Check the images before the volume goes back

Review a volume’s images while it is still at the station, because recapturing later means handling it again. FADGI’s metadata checks include “verifying the correct sequence and completeness of multi-page items,” and asks that pages be “in the correct order with no missing pages.”

  • Image count equals page count plus covers, spine and inserts.
  • Every page is sharp from the fore-edge into the gutter.
  • No fingers, weights or clips cover any writing.
  • No glare from glass or a shiny binding.
  • Pages with text lost in the binding are listed in the log.

Our image QC checklist has the full list, with completeness, image quality, file and recording checks.

Tight gutters, foldouts and text you cannot reach

Capture as far into the gutter as the binding allows without strain, include everything visible to the eye, and record the pages where text could not be reached. Foldouts are opened onto a support and captured in place.

The gutter

FADGI’s rule for general bound volumes is a good one for any volume: “The digital image should capture as far into the gutter as practical but must include all of the content that is visible to the eye.” If a reader looking into the opened book can see a word, the image should show it. If they cannot, forcing the book wider to reveal it is the damage this article is about.

Practical steps for tight gutters:

  1. Light both pages evenly from the side away from the gutter, so the inner margin is not lost in shadow.
  2. Capture each page separately with the camera square to it, rather than both pages at once from straight above.
  3. Hold a lifting page with a thin polyester strip or a microspatula at the margin, not with fingers.
  4. Leave the strip or spatula in the master image if it shows; FADGI says such implements “should not be edited out of master files” for rare material.
  5. Log the page numbers where text runs into the binding and was not fully captured, so researchers know the image is not the whole page.

Targets at page height

Reference targets sit at the level of the page being photographed. FADGI’s example is specific: “when digitizing a page in a thick book, make sure the reference targets are at the same height/level as the page being scanned.” As the text block moves from one board to the other, the target has to follow it. Our article on FADGI star ratings explains what those targets measure.

Foldouts and oversize plates

Foldouts are opened onto a support at the same height as the page, captured unfolded, and folded back along their original creases. The Library of Congress requires equipment with “a scanning bed that is as large or larger than the object to be scanned” for oversized materials, “including books that have foldouts.” Very large folded maps in atlases raise the stitching questions covered in our guide to digitizing oversize maps and drawings.

Brittle paper, red rot and loose parts

Brittle paper, crumbling leather and loose parts each need a slower method rather than a different machine. The common rule is to stop at the first sign of loss.

Brittle paper

Brittle pages crack where they flex, which in a book is the hinge and the corner where a finger turns the leaf. NEDCC recommends page turners for brittle material: “microspatulas, thin Teflon folders, or simple items made out of stiff paper.” Turn from the fore-edge with the full height of the turner under the leaf. If a corner breaks off, place the fragment in a labeled folder with the page number and note it in the capture log.

FADGI’s instruction for every bound category applies here word for word: “In any situation where there is potential harm to the original, stop immediately and seek assistance.”

Red rot

The Library of Congress defines red rot as “the powdery deterioration of leather, especially at the hinges of the book where the leather flexes.” It is present on many 19th and early 20th century leather bindings and “is not reversible but may be stabilized in some cases.” The powder transfers to hands, pages and the scanner.

For handling, the Library suggests that “a polyester film jacket can help prevent the transfer of leather rot from hands to the pages.” Do not apply leather dressing; the Library says plainly, “Do not oil or ‘dress’ leather books with oils or waxes of any sort.” Clean the cradle and work surface after each red-rot volume so the powder does not travel to the next book.

Loose boards, detached spines and inserts

A loose board will swing as the book opens, levering against the remaining joint. Support it on its own foam block. Loose slips, receipts and pressed flowers are captured where they were found, then left in place; record them in the log. Never use self-adhesive tape, rubber bands or glue to hold anything together during a session; the Library of Congress advises against all three for books in general.

The environment

FADGI asks that collection materials be “maintained at the same temperature and humidity while being imaged as they are maintained in the collection.” The Library of Congress guide warns that rapidly changing humidity is a concern for books and that very dry air can cause warping. Let volumes acclimate in their boxes, and keep the lights off between captures.

Ledgers, registers and letterpress copybooks

Ledgers, registers and copybooks are common in historical societies and county offices, and they share three traits: they are heavy, their writing runs into the gutter, and they matter page by page. Plan for all three.

Heavy and wide volumes

NEDCC advises storing “very large or heavy volumes lying flat,” and notes that “for very large or heavy volumes, two people may be necessary for handling.” At the scanner, that means a cradle sized to the volume, a second person for every move between shelf, cart and cradle, and no lifting by the spine. The Library of Congress guide’s shelf rule applies too: grip both sides of the spine at the middle of the book, never the top of the spine.

Writing into the gutter

When entries run close to the sewing, accept that some of them will be partly hidden, capture what is visible, and record the affected pages. If a volume’s text is essential and largely unreachable, that is a question for a conservator and a curator together, not for the operator at the scanner.

Letterpress copybooks

Letterpress copybooks hold copies of outgoing letters on very thin paper. The Library of Congress lists “letter copy books with very thin and acidic paper, such as carbon copy correspondence” among the materials that may be excluded pending treatment decisions. A sheet of plain white paper slipped behind each leaf during capture keeps the next page’s text from showing through, and a folder turns each leaf more safely than fingers.

Capture order and file names

Capture in a fixed order and name files so the order survives. A typical sequence: front cover, spine, any label, front pastedown and endpapers, every page including blanks if your policy says so, back endpapers, back cover. Our file naming builder produces consistent names for each image.

What the capture log should record for each volume

A short log per volume turns handling decisions into information a researcher can use later. Record at least:

  • the volume identifier and the date and operator of each session
  • the measured safe opening angle and the cradle angle actually used
  • the FADGI category, star level and resolution agreed for the volume
  • pages where text runs into the binding and was not fully captured
  • fragments, loose inserts and their positions
  • any stop, its cause and the decision that followed
  • the target reports for each session

Registers and ledgers in county offices may be permanent records under a retention schedule, so the log also shows later auditors how the images were made. Our page for local government records covers that setting.

Example (fictional). The Wren Gulch Mercantile day book in the Aster County Historical Society’s Box 3 has 212 pages and a split spine. The assessment records that it “opens safely to about 110 degrees,” so it is captured in a foam cradle set to that angle, one page at a time, with the camera tilted square to each page. Capture follows FADGI category 3.1 at three-star, 300 ppi, and produces 216 images: the 212 pages plus both covers, the spine and the label.

Page 77, the February 9, 1894 entry for the smelter boarding house (“flour 4 sacks, coffee 10 lbs., lamp oil 2 gal., on account”), is saved as ACHS-3-L077.tif. Three pages where figures run into the sewing are listed in the capture log, so anyone reading the totals knows a digit may sit in the binding.

Once ledger pages are captured, the handwriting becomes a text recognition question; tabular entries in a day book behave differently from letters.

Scrapbooks and albums

Scrapbooks are bound volumes whose contents fight the binding. NEDCC describes them well: they “often contain a variety of components and media,” may have “raised surfaces, three-dimensional decoration, or moving parts,” and “the addition of the scraps themselves causes the binding to bulge and be unduly stressed.”

Capture the page, then the pieces

Capture each page whole first, as the compiler arranged it. Then capture separately anything with information hidden from that view: the back of a clipping that is attached only at one edge, a folded program, a pocket of letters. Lift an item only if it lifts without force; never peel glued items to see behind them.

FADGI’s metadata guidance asks for a convention when one page produces several views. Its example names “a double page spread, each individual page, and a close-up section of a page,” and says the convention “should match with the actual image files.” Decide the suffixes before the session, for example _page, _detail01 and _verso, and keep to them.

Raised and fragile items

Pressed flowers, ribbons, hair, badges and photographs make a scrapbook page three-dimensional. The Library of Congress lists “paper documents with three-dimensional objects (e.g., medals, seals, ribbons) attached” and “photographs that are separating from the mount or support” among materials that may be excluded pending treatment. Do not lay glass over any of them, and light from a low angle only if the item can tolerate it.

Photograph albums

Albums combine a binding with photographs, so both sets of rules apply. The Library of Congress asks technicians to wear gloves when handling photographs, unlike paper. Its exclusion list includes photographs that are “curled, bent, creased, folded, wrinkled, cockled or cracked,” which describes many album prints mounted on stiff, warped leaves.

FADGI’s notes for prints and photographs say glass may hold a photograph flat “only when the original will not be harmed by doing so,” and that “tightly curled materials must not be forced to lay flat.” Where glass is used, FADGI highly recommends anti-reflective glass to reduce glare and Newton’s rings.

Capture the album page whole first, then each photograph on it, and capture any caption or inscription that sits on the mount or the facing leaf. Prints that can be lifted from corner mounts without force may be imaged front and back; prints glued to the page stay where they are. Our photo and negative scanning page explains how fronts, backs and mounts are linked by file name.

Disbound albums

Some scrapbooks arrive already falling apart. NEDCC notes that for scrapbooks “very damaged and that do not have value to the institution as an object, pages can be removed, numbered, put into individual folders, and boxed.” That is a collections decision about the object, made by the institution, not a shortcut for the scanner.

Do fragile books have to be cut apart to scan?

No. The handling rules of the Library of Congress, FADGI and NEDCC all assume the book stays bound, and a volume that cannot be opened far enough waits for treatment or is captured within its limits.

FADGI is explicit about what cutting changes. “If a book is ‘guillotined’ for the purpose of scanning, it is no longer considered to be a book for the purposes of FADGI compliance.” It is then imaged as loose documents. Cutting a volume to make scanning faster turns an original into something else.

There are honest cases where pages are separated. A binding may already have failed. A conservator may disbind a volume to treat it and rebind it afterward, and scanning during that window is efficient. An institution may decide, as NEDCC describes for damaged scrapbooks, that the leaves matter more than the object. In each case the decision comes from the collection’s owner and a conservator, and FADGI’s rule follows: “If a volume is dis-bound, the FADGI recommendations apply as if the volume was individual pages, capturing all edges of the page.”

Questions to ask before anyone scans your bound volumes

Whether volunteers, staff or a vendor will do the work, a few written answers show whether the method fits your volumes. Ask them before the first volume leaves the shelf.

  1. What is the widest a volume will be opened, and who measures it before capture?
  2. What kind of cradle supports the boards, and can the camera or scan head be adjusted to the volume’s height and angle?
  3. When is glass placed on a page, and who approves it for rare material?
  4. Are pages turned by hand? What page turners are used for brittle leaves?
  5. How is lighting heat controlled, and has the surface temperature rise been measured?
  6. How far into the gutter will images reach, and how are pages with hidden text recorded?
  7. How are foldouts, loose inserts and scrapbook items handled and named?
  8. Who decides to stop when a page tears or a joint cracks, and what happens next?
  9. Are volumes kept at their storage temperature and humidity during capture?
  10. How were the operators trained to handle bound materials?
  11. How will volumes travel, and are they laid flat and wrapped in transit?

For the last question, our packing and transport checklist lists what to require, including “bound volumes wrapped and laid flat, never on their fore-edge.” The collection care page describes custody and handling of originals more broadly.

What to do next

  1. Measure and record the safe opening angle of each volume in your inventory.
  2. Sort volumes into the triage routes above and set aside any that need a conservator.
  3. Pick two or three representative volumes, including your most difficult one, for a test run.
  4. Review the test images for gutter reach, glare and completeness before approving the rest.

A small first batch is the cheapest place to find out whether a method suits your bindings. Our guide to running a digitization pilot explains how to set one up, and the document scanning page describes how Dastok, a Colorado Springs company that digitizes historical documents, photographs and museum collections, captures bound volumes in cradles at the angle each binding allows.

Working through this with a real collection?

If this article describes a decision you are facing, tell us about the collection. A pilot box answers most questions with your own material.

Plan a pilot box

Studio and contacts

24 South Weber Street, Suite 225
Colorado Springs, CO 80903
(719) 244-8450sales@dastok.com